HP Surestore Disk Array 12h SGI IRIX Configuration Guide - Page 22

22

hp surestore disk array xp operating system configuration guide: SGI IRIX

Origin BASEIO board, module 1 slot 1: Revision 4

Origin FIBRE CHANNEL board, module 1 slot 4: Revision 4


Origin PCI XIO board, module 1 slot 2: Revision 4

IOC3 external interrupts: 1#

LUN 0 is implied when no LUN is listed.

Example (Fabric)

#

hinv

4 250 MHZ IP27 Processors

CPU: MIPS R10000 Processor Chip Revision: 3.4

FPU: MIPS R10010 Floating Point Chip Revision: 0.0

Main memory size: 2048 Mbytes

Instruction cache size: 32 Kbytes

Data cache size: 32 Kbytes

Secondary unified instruction/data cache size: 4 Mbytes

Integral SCSI controller 2: Version Fibre Channel AIC-1160, revision 2

Integral SCSI controller 0: Version QL1040B (rev. 2), single ended

Disk drive: unit 1 on SCSI controller 0

CDROM: unit 6 on SCSI controller 0

Integral SCSI controller 1: Version QL1040B (rev. 2), single ended




Integral SCSI controller 8: Version Fibre Channel QL2200

Fabric Disk: node 50000e10ff809999 port 0 lun 0 on SCSI controller 8











IOC3 serial port: tty1

IOC3 serial port: tty2

Integral Fast Ethernet: ef0, version 1, module 1, slot io1, pci 2


Origin BASEIO board, module 1 slot 1: Revision 4


Origin PCI XIO board, module 1 slot 2: Revision 4


IOC3 external interrupts: 1

5.

Verify that all new devices on the disk array are listed in this file.

Section	Page
Contents	3
About This Manual	5
Revision History	6
Updates	7
SGI IRIX Installation	9
Hardware Installation	9
Fabric	10
Disk Array FC Port	10
Remote Console PC and LUN Configuration Manager Installation	10
Preparing for Disk Array Device Configuration	11
Installation Requirements	12
XP256	12
Fibre Channel Interface	12
Connectivity Options	12
Device Types	13
Installation Procedures	14
Identify the Available SCSI Paths (XP256 Only)	15
To identify the available SCSI paths:	15
Prepare the Disk Array	16
To install the disk array, the HP service representative performs the following tasks:	16
Setting the Host Mode for the Disk Array Ports	16
Configuring the Disk Array Fibre Channel Ports	16
Port Address	17
Loop ID Conflict	18
Define the SCSI Paths (XP256 Only)	19
To define the SCSI paths for the new devices:	19
Connect the Disk Array	20
To connect the disk array:	20
Verify New Device Recognition	21
To verify the system recognizes the devices on the newly installed disk array:	21
Create the Device Files	23
Fabric Switch	23
To create the device files:	24
Partition and Label the Devices	26
To partition and label the devices:	26
Enable Command Tag Queuing	29
To enable command tag queuing and set the queue depth for the disk array devices:	29
Create the File Systems	31
To create an EFS file system:	31
To create an XFS file system:	31
Create and Verify the Mount Directories	32
To create and verify the mount directories:	32
Register, Mount, and Verify the File Systems	33
To register the new file systems in the mount table:	33
To mount and verify the new file systems:	34
Troubleshooting	35
Calling the HP Support Center	36
SCSI Path Worksheet	37
Disk Parameters	39
Notes for Table1 Through Table5	46
SCSI TID Map for Fibre Channel Adapters	47
Byte Information Table	49
Queue Depth Parameters Table	50
Parameter Tables for OPENK/3/8/9/E Devices	51
Notes for Parameter Tables for OPENK/3/8/9/E Devices	54
Physical Partition Size Table	57
Host Bus Adapter Modes	59
Supported Host Modes	61
Failover and SNMP Remote Disk Array Management	63
Failover Configuration	64
SNMP Configuration	65
Glossary	67

HP Surestore Disk Array 12h SGI IRIX Configuration Guide - Page 22

Example Fabric, LUN 0 is implied when no LUN is listed.

Page 22 highlights