HP Tc2110 hp server tc2110 NOS installation guide (English) - Page 15

PHASE 4 – Con the Network, b. Insert the HP Server tc2110 Windows NT LAN driver HP disk NT LAN

Get HP Tc2110 - Server - 128 MB RAM PDF manuals and user guides View all HP Tc2110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Chapter 3 Installing Microsoft Windows NT 4.0 Server NOTE Your CD-ROM drive needs few seconds to detect the newly inserted CD-ROM. If the window "Files Needed" appears, press Enter again. 2. Click Next at the Windows NT Server Setup screen to gather information about your computer. 3. You can now proceed through the customization of your installation using the graphical interface. NOTE You can later promote your "Backup domain controller" to "Primary domain controller" and vice versa. "Stand Alone Server" cannot be promoted to "Primary Domain Controller" or demoted to "Backup Domain Controller". 4. Emergency repair disk: HP recommends you create this disk because it saves your Windows NT Server Setup configuration. Prepare a blank formatted floppy diskette to create this disk then click Next. You do not need to insert the blank floppy diskette at this time as Windows NT Setup will actually perform the disk creation at the end of you configuration phase. PHASE 4 - Configure the Network 1. Click Next at the Windows NT Setup screen to install Windows NT Networking. 2. Click Next at the following window to use the network adapter embedded with your HP Server tc2110. 3. Click Next to accept installing the Microsoft Internet Information Server. 4. When you reach the Network Adapters screen, do NOT select Start Search. Instead, click the Select from list... button to load the HP LAN driver: a. Select the Have Disk button when given a list of Network Adapter drivers, to use HP specific driver b. Insert the HP Server tc2110 Windows NT LAN driver (HP disk NT LAN #1) then press Enter c. Press Enter to validate the selection of the "Intel® PRO Adapter", then Enter again to confirm the Network Adapters selection. d. When prompted, insert the second driver disk (HP disk NT LAN #2). 5. Follow the on-screen instructions to complete the selection of the Network Protocols and Network Services. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
Chapter
3
Installing Microsoft Windows NT 4.0 Server
NOTE
Your CD-ROM drive needs few seconds to detect the newly
inserted CD-ROM. If the window "Files Needed" appears,
press Enter again.
2.
Click Next at the Windows NT Server Setup screen to gather information
about your computer.
3.
You can now proceed through the customization of your installation using
the graphical interface.
NOTE
You can later promote your "Backup domain controller" to
"Primary domain controller" and vice versa.
"Stand Alone
Server" cannot be promoted to "Primary Domain Controller" or
demoted to "Backup Domain Controller".
4.
Emergency repair disk: HP recommends you create this disk because it saves
your Windows NT Server Setup configuration. Prepare a blank formatted
floppy diskette to create this disk then click Next. You do not need to insert
the blank floppy diskette at this time as Windows NT Setup will actually
perform the disk creation at the end of you configuration phase.
PHASE 4 – Configure the Network
1.
Click Next at the Windows NT Setup screen to install Windows NT
Networking.
2.
Click Next at the following window to use the network adapter embedded
with your HP Server tc2110.
3.
Click Next to accept installing the Microsoft Internet Information Server.
4.
When you reach the Network Adapters screen, do NOT select Start Search.
Instead, click the Select from list… button to load the HP LAN driver:
a. Select the Have Disk button when given a list of Network Adapter
drivers, to use HP specific driver
b. Insert the HP Server tc2110 Windows NT LAN driver (HP disk NT LAN
#1) then press Enter
c. Press Enter to validate the selection of the "Intel® PRO Adapter", then
Enter again to confirm the Network Adapters selection.
d. When prompted, insert the second driver disk (HP disk NT LAN #2).
5.
Follow the on-screen instructions to complete the selection of the Network
Protocols and Network Services.
9