Home » HP Manuals » Desktops » HP Tc2110 » Manual Viewer

HP Tc2110 hp server tc2110 NOS installation guide (English) - Page 63

Installing TurboLinux Server 6.5, Prepare the Installation, High Level Process Flow

Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

8 Installing TurboLinux Server 6.5 Prepare the Installation Please refer to the Chapter 1 "Preparing your HP Server tc2110 for your NOS installation" for our recommendations on the server preparation. Then gather the following material: · HP Server tc2110 Startup CD · TurboLinux Server 6.5 CD-ROM · A blank 3.5-inch diskette, labeled TurboLinux 6.5 Boot Disk (Optional) · Two or more clients for testing purpose (Optional) High Level Process Flow 1. Perform TurboLinux 6.5 installation. 2. Install additional HP accessories. Section 1. Perform TurboLinux Installation PHASE 1 - Launch the Installation 1. Turn on the server and insert the Turbolinux Server 6.5 CD-ROM. 2. Press Enter to start installation. 3. Wait as the system prepares for the installation. 4. Choose your language then press Enter to proceed with the installation. PHASE 2 - Configure the Server The installation program now displays a graphical interface. You can proceed through the customization of your installation. Please note the following recommendations: · HP recommends using the default Install Class, which is Standard Install. 57

Section	Page
1HP Server tc2110 Installation Highlights for Experts	7
Section 1. Introduction	7
Section 2. Installation Highlights	7
2Preparing your HP Server tc2110 for your NOS installation	9
Section 1. Hardware Setup	9
Preparing your Hard Disk Drives	9
Section 2. Updating your Server BIOS	9
Section 3. Run HP Diagtools	10
Section 4. Using the Startup CD	10
3Installing Microsoft Windows NT 4.0 Server	11
Prepare the Installation	11
High Level Process Flow	11
Section 1. Create the Drivers Diskettes	11
Section 2. Create Microsoft Windows NT Installation Diskettes	12
Section 3. Perform Windows NT Installation	12
PHASE 1 – Drivers Installation	13
PHASE 2 – Hard Drive Preparation	13
PHASE 3 - System Configuration Details	14
PHASE 4 – Configure the Network	15
PHASE 5 – Completing the Installation	16
PHASE 6 – Install the Service Pack	17
PHASE 7 – Install HP Video Driver	18
Section 4. Initialize Hard disk Drive	18
Section 5. Perform Hardware Status Check	19
Section 6. Attach Clients to Network and Test Network Link	19
Section 7. Install Additional HP Accessories	20
Troubleshooting	20
Tip #1. Troubleshooting SCSI Host Bus Adapter Configuration	21
Tip #2. NT Warning About Drives with More than 1024 Cylinders	21
Tip #3. Service Pack Files Replaced Without Feedback	22
Tip #4. Using the NT Event Log to Diagnose Network Adapter Problems	22
Tip #5. Booting from Another SCSI HDD	23
Tip #6. Restarting Windows NT installation	23
On-Line Information and Software Sources	23
4Installing Microsoft Windows 2000 Server and Small Business Server 2000	25
Prepare the Installation	25
High Level Process Flow	25
Section 1. Create the Drivers Diskettes	25
Section 2. Perform Windows 20000 Installation	26
Section 3. Completing the Installation	28
PHASE 1 – Install the Service Pack	28
PHASE 2 – Install the Chipset Driver	29
PHASE 3 – Install the HP Video Driver	29
PHASE 4 – Install the HP LAN driver	30
PHASE 5 – Install Windows 2000 Recovery Console	30
Section 4. Configure the System	30
PHASE 1 – Perform Hardware Status Check	30
PHASE 2 - Initialize Hard Disk Drive	31
PHASE 3- Adding Terminal Server Services	32
Section 5. Configure the Network	34
PHASE 1 -- Configure Server IP Address	34
PHASE 2 -- Attach Clients to Network and Test Network Link	34
PHASE 3 -- Domain Controller Setup	35
Section 6. Install Additional HP Accessories	36
Troubleshooting	37
Tip #1. Upgrading from NT 4.0 to Windows 2000	37
Tip #2. Windows 2000 Installation Halts About Three Minutes After Starting to Boot from CD-ROM	37
Tip #3. Configure the Parallel (LPT) Port for ECP Mode	38
Tip #4. Windows 2000 Drivers Signatures	38
Tip #5. Windows 2000 Recovery Options	39
Tip #6. Restarting Windows 2000 installation	41
Online Information and Software Sources	41
5Installing Novell NetWare 5.1 and Novell Small Business Suite 5.1	43
Prepare the Installation	43
High Level Process Flow	43
\	43
Section 2. Create the Drivers Diskettes	43
Section 3. Perform NetWare 5.1 or Novell Small Business Suite 5.1 Installation	44
PHASE 1 – Start the Installation	44
PHASE 2 – Install HP Drivers	46
PHASE 3 – Configure the Network	47
Section 4 Install the Support Pack	48
Section 5. Install Additional HP Accessories	49
Troubleshooting	50
Tip #1. Restarting NetWare Installation	50
On-Line Information and Software Sources	50
6Installing Novell NetWare 6.0 and Novell Small Business Suite 6.0	51
Prepare the Installation	51
High Level Process Flow	51
Section 1. Run HP Diagtools (optional)	51
Section 2. Create the Driver’s Diskettes	51
Section 3. Perform NetWare 6.0 or SBS 6.0 Installation	52
PHASE 1 – Start the Installation	52
PHASE 2 – Install HP Drivers	54
PHASE 3 – Configure the Network	55
Section 4. Install Additional HP Accessories	56
Troubleshooting	57
Tip #1. Restarting NetWare Installation	57
On-Line Information and Software Sources	57
7Installing Red Hat Linux 7.1	59
Prepare the Installation	59
High Level Process Flow	59
Section 1. Perform Red Hat Linux Installation	59
PHASE 1 – Launch the Installation	59
PHASE 2 – Configure the Server	59
PHASE 3 – Complete the Installation	60
Section 2. Install Additional HP Accessories	61
On-Line Information and Software Sources	61
8Installing TurboLinux Server 6.5	63
Prepare the Installation	63
High Level Process Flow	63
Section 1. Perform TurboLinux Installation	63
PHASE 1 – Launch the Installation	63
PHASE 2 – Configure the Server	63
PHASE 3 – Complete the Installation	64
Section 2. Install Additional HP Accessories	64