Home » HP Manuals » Desktops » HP Tc2120 » Manual Viewer

HP Tc2120 HP 2100S SCSI RAID - User Guide (337208-001) - Page 18

Cache Memory Module, Adapted SCSI RAID Controller LEDs, LED Display During Power-Up

UPC - 808736945332

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

About Your New Controller Cache Memory Module SDRAM memory provides 32 MB, 64 MB, or 128 MB of high-speed disk cache for Adaptec SCSI RAID controllers. If ECC memory is installed, the cache is protected by ECC, which automatically repairs errors in the data. The green ECC Enabled LED is lit when ECC memory is installed. For the location of this LED, refer to "Board Layout" in this chapter. Adapted SCSI RAID Controller LEDs Adaptec SCSI RAID controllers provide nine LEDs that let you visually monitor controller activity. Several different controller states are indicated by the LED as outlined in the following sections. Two additional LEDs indicate the status of the cache memory on the controller. For the location of the LEDs on your controller, refer to "Board Layout" in this chapter. LED Display During Power-Up During its power-up sequence, the controller passes through the following states in sequence, as indicated by the LEDs: NOTE: The address translation unit (ATU), PCI bridge, and cache module (if installed) must be configured and enabled before the I2O initialization can be completed. If any one of these components are not configured or become disabled during the Fast Idle phase, the pattern will return to the respective wait pattern for the affected component. 2-6 HP 2100S SCSI RAID Controller User Guide

Section	Page
HP 2100S SCSI RAID Controller User Guide	1
Notice	2
Contents	3
About This Guide	7
Audience Assumptions	7
Important Safety Information	7
Symbols on Equipment	7
Symbols in Text	8
Getting Help	9
Technical Support	9
HP Website	9
Authorized Reseller	10
Reader’s Comments	10
Chapter 1: Introduction	11
Read This First	11
About the Documentation	11
System Requirements	12
Working with Electricity	12
Preventing Electrostatic Discharge	12
Chapter 2: About Your New Controller	13
Introduction	13
Adaptec SCSI RAID Feature Overview	13
DC Power Requirements	14
Environmental Specifications	15
Cache Memory	15
2100S Features	15
Board Layout	17
Cache Memory Module	18
Adapted SCSI RAID Controller LEDs	18
LED Display During Power-Up	18
LED Display During Controller Idle	19
LED Display During Controller Active	19
Cache Status LEDs	20
Chapter 3: Installing Your Controller	21
Installation Overview	21
Configuration	22
Narrow and Wide SCSI	22
Configuring Cables	22
Configuring SCSI Termination	23
Configuring Device IDs	25
Installation	25
Installing Cache Memory Modules	25
Installing the Controller	26
Determining the Booting Controller	27
Controller IRQ and Address	27
NVRAM Reset	28
Chapter 4: Installing Adaptec SCSI RAID Software	29
Microsoft Windows 2000	29
Power Management with Windows 2000	29
Installing on a New System	30
Adding to an Existing System	31
Appendix A: Regulatory Compliance Notices	32
Regulatory Compliance Statements	32
Federal Communications Commission Radio Frequency Interference Statement	32
European Union Compliance Statement	33
Australian/New Zealand Compliance Statement	34
Canadian Compliance Statement	34
Japanese Compliance (Voluntary Control Council Initiative)	34
End-User Software License Agreement	34
Appendix B: Electrostatic Discharge	37
Grounding Methods	38
Appendix C: Troubleshooting	39
	39
Problem 1	39
Solution 1	39
Problem 2	40
Solution 2	40
Problem 3	40
Solution 3	40
Problem 4	41
Solution 4	41
Problem 5	41
Solution 5	41
Problem 6	42
Solution 6	42
Problem 7	43
Solution 7	43
Problem 8	43
Solution 8	43
Problem 9	44
Solution 9	44
Problem 10	44
Solution 10	44
Problem 11	45
Solution 11	45
Problem 12	45
Solution 12	45
Problem 13	46
Solution 13	46
Problem 14	46
Solution 14	46
Problem 15	47
Solution 15	47
Problem 16	47
Solution 16	47
Problem 17	48
Solution 17	48
Problem 18	48

Match case Limit results 1 per page

About Your New Controller

Cache Memory Module

SDRAM memory provides 32 MB, 64 MB, or 128 MB of high-speed disk cache for

Adaptec SCSI RAID controllers. If ECC memory is installed, the cache is protected

by ECC, which automatically repairs errors in the data. The green ECC Enabled LED

is lit when ECC memory is installed. For the location of this LED, refer to “Board

Layout” in this chapter.

Adapted SCSI RAID Controller LEDs

Adaptec SCSI RAID controllers provide nine LEDs that let you visually monitor

controller activity. Several different controller states are indicated by the LED as

outlined in the following sections. Two additional LEDs indicate the status of the

cache memory on the controller. For the location of the LEDs on your controller,

refer to “Board Layout” in this chapter.

LED Display During Power-Up

During its power-up sequence, the controller passes through the following states in

sequence, as indicated by the LEDs:

NOTE:

The address translation unit (ATU), PCI bridge, and cache module (if installed) must

be configured and enabled before the I

O initialization can be completed. If any one of these

components are not configured or become disabled during the Fast Idle phase, the pattern will

return to the respective wait pattern for the affected component.

2-6

HP 2100S SCSI RAID Controller User Guide