Home » HP Manuals » Desktops » HP Xw8200 » Manual Viewer

HP Xw8200 Adaptec SCSI RAID 2120S: Software Reference Guide - Page 320

Default Switch Values, Example, VERIFY, VERSION

UPC - 882780210455

Add to My Manuals
Save this manual to your list of manuals

Page 320 highlights

Adaptec SCSI RAID Software Reference Guide This might take a few minutes. Writing Adaptec 2200S (4MB) Flash Image to controller 0...OK. Verifying...OK Please restart the computer to allow firmware changes to take effect. VERIFY The VERIFY command compares the contents of each of the flash components on a controller to the corresponding image in a UFI file and indicates whether they match. Use this command to determine whether a controller's flash components are up-to-date when compared to a specific UFI file. Because the VERIFY command interrupts the controller's normal operation, you must reset the controller upon completion of this command. Default Switch Values If you do not include the /C switch, the AFU returns a fatal error message. If you do not include the /D switch, the AFU verifies against UFI files in the current default drive and directory. Example A:\> AFU VERIFY /C 0 Adaptec Flash Utility V4.0-0 B5749 (c)Adaptec Inc. 1999-2002. All Rights Reserved. Reading flash image file (Build 5748) Controller #0: Adaptec 2200S ROM: Checksum: 797B [VALID] (Build 5748) File: Checksum: 797B [VALID] (Build 5748) Image Compares Correctly VERSION The VERSION command displays version information about the flash components on a controller. 12-12

Section	Page
Adaptec SCSI RAID 2120S/2200S Software Reference Guide	1
Contents	3
1 Getting Started	23
Audience	24
Supported Platforms	24
Organization	24
Conventions	25
Related Documentation	26
2 Accessing the Command Line Interface	27
Accessing the CLI from the MS-DOS Prompt	28
Accessing the CLI from the Windows Start Button	28
To access the CLI from the UNIX/Linux prompt, display a window and type aaccli in any directory. ...	29
Accessing the CLI from the NetWare Server Console	29
Accessing the CLI from the UNIX Prompt	29
3 Syntax and Conventions for CLI Commands	31
CLI Features	31
CLI Command Syntax	32
CLI Parameter and Switch Value Types	34
CLI Status Information	40
4 General Control Commands	43
close	44
exit	44
help, ?	44
history_size	45
open	45
reset_window	47
toggle_more	47
5 container Commands	49
container add_level	51
container create mirror	53
container create mmirror	57
container create mstripe	62
container create mvolume	67
container create raid5	72
container create stripe	78
container create volume	83
container delete	88
container extend file_system	91
container extend mvolume	94
container extend volume	98
container list	102
container lock	113
container move	115
container promote	117
container readonly	120
container readwrite	122
container reconfigure	124
container release_cache	131
container remove drive_letter	132
container remove failover	134
container remove file_system	136
container remove global_failover	138
container restore RAID5	140
container scrub	142
container set cache	145
container set failover	149
container set global_failover	151
container set io_delay	153
container set label	156
container show cache	158
container show failover	164
container split	165
container unlock	169
container unmirror	171
6 controller Commands	173
controller details	174
controller firmware compare	179
controller firmware save	180
controller firmware update	182
controller list	183
controller pause_io	185
controller rescan	188
controller reset_scsi_channel	189
controller resume_io	190
controller set automatic_failover	191
controller set array_verify	193
controller show automatic_failover	195
controller show channels	196
controller show array_verify	199
7 disk Commands	201
disk blink	202
disk initialize	203
disk list	205
disk remove dead_partitions	209
disk set default	211
disk set smart	213
disk show default	216
disk show defects	217
disk show partition	219
disk show smart	222
disk show space	226
disk verify	229
disk zero	231
8 diagnostic Commands	233
diagnostic clear boot_parameters	234
diagnostic dump structures	235
diagnostic dump text	236
diagnostic load_arrays	238
diagnostic moderation set count	239
diagnostic moderation set timer	240
diagnostic moderation show count	241
diagnostic moderation show timer	242
diagnostic set boot_parameter	243
diagnostic show boot_parameter	244
diagnostic show history	245
9 logfile Commands	247
logfile end	248
logfile start	249
10 task Commands	251
task list	252
task resume	258
task stop	260
task suspend	262
11 enclosure Commands	265
enclosure activate slot	267
enclosure identify slot	269
enclosure list	271
enclosure prepare slot	276
enclosure set alarm	278
enclosure set door	279
enclosure set fan	280
enclosure set interval	282
enclosure set power	284
enclosure set scsiid	286
enclosure set temperature	289
enclosure show fan	291
enclosure show power	294
enclosure show slot	297
enclosure show status	301
enclosure show temperature	305
12 Using the Adaptec Flash Utility	309
Introduction	309
Overview of the AFU	310
System Requirements	311
Firmware Floppy Kit	312
Running the AFU	313
Accessing the AFU from the GUI	313
Accessing the AFU from the Command Line	313
Flashing the Firmware Using AFU	315
AFU Commands	316
AFU Error Handling	321
13 Using the Array Configuration Utility	323
Introducing the Array Configuration Utility for MS-DOS	323
Running the ACU	324
Using Interactive Mode	325
Using Script Mode	330
A Automated Scripts	351