HP Z4 Maintenance and Service Guide - Page 49

Computer Setup F10 Utilities

Get HP Z4 PDF manuals and user guides View all HP Z4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Table 5-3 Computer Setup-Advanced (for advanced users) (continued) Option Heading Controls virtualization DMA remapping features of the chipset. Changing this setting requires turning the computer off and then back on. Default is disabled. PCI Express Slot x (enable/disable) Lets you disable individual expansion slots. Allow PCIe/PCI SERR# Interrupt (enable/disable) Allows PCI devices to report PCI/PCIe System Error signals, such as address parity errors, data parity errors, and critical errors other than parity. Default is enabled. Power Button Override (disable/4 sec/15 sec) Lets you disable or enable and select the number of seconds you have to hold down the power button for it to force the system to power off. Default is '4 sec'. Built-In Device Options Embedded LAN Controller Select to show the device in the operating system. Default is enabled. Wake On LAN Lets you either disable the Wake On LAN feature, or configure where the computer boots, including the network or hard drive. Default is Boot to Network. Missing Dust Filter Select to display a message when a dust filter is not installed. Audio Device Select to show the device in the operating system. Default is enabled. Internal Speakers (does not affect external speakers) Clear to disable the chassis speaker or speakers. This function is applicable to normal audio playback in the operating system and does not affect the error or warning beeps during POST. Default is enabled. Increase PCIe Idle Fan Speed(%) Sets idle fan speed percentage. This setting only changes the minimum fan speed. The fan is still automatically controlled. Port Options Allows you to hide the following ports from the operating system: ● Serial port A ● Serial port B ● SATA0 thru SATA7 ● eSATA0 ● eSATA1 ● Internal USB ports ● Front USB ports ● Rear USB ports ● USB Type-C Controller(s) firmware version ● Media card reader Option ROM Launch Policy These policies control whether Legacy Option ROMs or UEFI drivers are loaded. Default is 'All UEFI.' Configure Option ROM Launch Policy Computer Setup (F10) Utilities 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
Table 5-3
Computer Setup—Advanced (for advanced users) (continued)
Option
Heading
Controls virtualization DMA remapping features of the chipset. Changing this setting requires turning
the computer
off
and then back on. Default is disabled.
PCI Express Slot x
(enable/disable)
Lets you disable individual expansion slots.
Allow PCIe/PCI SERR# Interrupt
(enable/disable)
Allows PCI devices to report PCI/PCIe System Error signals, such as address parity errors, data parity
errors, and critical errors other than parity. Default is enabled.
Power Button Override
(disable/4 sec/15 sec)
Lets you disable or enable and select the number of seconds you have to hold down the power button for
it to force the system to power
off.
Default is ‘4 sec’.
Built-In Device Options
Embedded LAN Controller
Select to show the device in the operating system. Default is enabled.
Wake On LAN
Lets you either disable the Wake On LAN feature, or
configure
where the computer boots, including
the network or hard drive. Default is Boot to Network.
Missing Dust Filter
Select to display a message when a dust
filter
is not installed.
Audio Device
Select to show the device in the operating system. Default is enabled.
Internal Speakers
(does not
affect
external speakers)
Clear to disable the chassis speaker or speakers. This function is applicable to normal audio playback in
the operating system and does not
affect
the error or warning beeps during POST. Default is enabled.
Increase PCIe Idle Fan Speed(%)
Sets idle fan speed percentage. This setting only changes the minimum fan speed. The fan is still
automatically controlled.
Port Options
Allows you to hide the following ports from the operating system:
●
Serial port A
●
Serial port B
●
SATA0 thru SATA7
●
eSATA0
●
eSATA1
●
Internal USB ports
●
Front USB ports
●
Rear USB ports
●
USB Type-C Controller(s)
firmware
version
●
Media card reader
Option ROM Launch
Policy
These policies control whether Legacy Option ROMs or UEFI drivers are loaded. Default is ‘All UEFI.’
Configure
Option ROM Launch Policy
Computer Setup (F10) Utilities
41