Home » Hitachi Manuals » Projection Televisions » Hitachi 43FDX01B » Manual Viewer

Hitachi 43FDX01B Service Manual - Page 29

Circuit Descriptions, Abbreviation List, and IC Data Sheets - part list

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Circuit Descriptions, Abbreviation List, and IC Data Sheets LGE PDP 2K6 9. EN 29 9. Circuit Descriptions, Abbreviation List, and IC Data Sheets Index of this chapter: 9.1 Introduction 9.2 Power Supply Unit (PSU) 9.3 Control Board 9.4 X Board 9.5 Y Sustain Board 9.6 Y Drive Board 9.7 Z Sustain Board 9.8 DC/DC Converter Part 9.9 FPC (Flexible Printed Circuit) 9.10 FFC (Flat Flexible Cable) 9.11 TCP (Tape Carrier Package) 9.12 IPM (Intelligent Power Modules) 9.13 Abbreviation List 9.14 IC Data Sheets 9.1 Introduction The 42X3* panel is LGE's HD successor for the year 2007 of the 42V7* panel. 9.2 Power Supply Unit (PSU) 9.2.1 Purpose • To convert an input voltage of 100 ~ 240 Volt AC to voltages that the different boards and the panel need. • Output voltages: Vcc (5 V), Vs (180 ~ 200 V), and Va (60 ~ 65 V), all DC. • The PSU switches "OFF" automatically, when it detects errors like short circuits. Warning: Voltages on the PSU reach 390 Volt maximum, so be very careful when handling it! Figure 9-1 Power supply G_16391_006.eps 020707

Section	Page
Content	1
1. Technical Specifications, Connections, and Chassis Overview	2
1.1 Technical Specifications PDP42X3*	2
1.1.1 General Specification	2
Table 1-1 General Specifications	2
1.1.2 Definitions	2
Figure 1-1 Definition of module position	2
Figure 1-2 Identification label	2
Figure 1-3 Voltage label (on rear side of module)	2
Figure 1-4 Part number printing (on board)	3
Figure 1-5 Part number label (on board)	3
Figure 1-6 TCP serial number (on TCP)	3
1.1.3 Chassis Overview	4
Figure 1-7 PWB location	4
2. Safety Instructions, Warnings, and Notes	5
2.1 Warnings	5
3. Directions for Use	6
4. Mechanical Instructions	7
4.1 Mechanical Overviews	7
Figure 4-1 Cable dressing	7
Table 4-1 Cable function	7
Figure 4-2 Label location on PWB’s	8
Figure 4-3 Label indication	8
Figure 4-4 Label information (1)	9
Figure 4-5 Label information (2)	9
4.2 Panel/assy removal	9
4.2.1 Power Supply Unit	9
Figure 4-6 PSU removal	9
4.2.2 Control Board	9
Figure 4-7 Control board removal	9
4.2.3 Y Sustain Board	10
Figure 4-8 Y-SUS board removal	10
4.2.4 Y Driver Board	10
Figure 4-9 Y driver board removal	10
Figure 4-10 TCP Separation	10
4.2.5 Z-Sustain board	11
Figure 4-11 Z-SUS board removal	11
Figure 4-12 FPC removal	11
4.2.6 X-board	11
Figure 4-13 X board removal 1/2	11
Figure 4-14 X board removal 2/2	11
Figure 4-15 TCP Separation	11
5. Service Modes, Error Codes, and Fault Finding	12
5.1 Quick Module Check	12
Figure 5-1 Logical judgement	12
Figure 5-2 Quick check	12
5.1.1 No Display	13
Connectors	13
Figure 5-3 Control + Y-SUS board	13
Figure 5-4 Control + Z-SUS board	13
Figure 5-5 Control + X board	13
Figure 5-6 Signal input (LVDS)	13
Exhaust Tip	13
Figure 5-7 Exhaust tip \	13
PSU (see figure “PSU trouble shooting“)	14
Figure 5-8 PSU trouble shooting	14
PSU Power Protection	14
5.1.2 Bar Defect (Vertical)	15
Connector	15
Figure 5-9 Connector check (1)	15
Figure 5-10 Connector check (2)	15
Checking the TCP	15
Figure 5-11 TCP torn	15
Figure 5-12 TCP IC broken	15
Control Board	15
Figure 5-13 Control board address flow	15
5.1.3 Line Defect (Vertical)	15
Line Open or Short	15
Figure 5-14 Single line defect	15
Line Open or Short with the Same Distance	16
Figure 5-15 Evenly repeated lines	16
5.1.4 Bar Defect (Horizontal)	16
Connector	16
Figure 5-16 Check FPC connectors	16
Figure 5-17 Check drive connectors	16
Scan IC Check	16
Figure 5-18 Scan IC output diode check	16
5.1.5 Line Defect (Horizontal)	16
FPC Check	16
Figure 5-19 Open FPC electrode / Panel electrode breakdown	16
Scan IC Check	17
Figure 5-20 Scan IC output diode check	17
5.1.6 Mis-discharge Defect	17
Figure 5-21 Mis-discharge	17
Checking Order	17
How to Check an IPM	17
Forward direction	17
Reverse direction	17
Figure 5-22 IPM check	17
5.2 Detailed Module Check	17
5.2.1 No Display	17
The Screen Does Not Display a Picture	17
Figure 5-23 Output waveforms on X, Y, and Z-boards	18
5.2.2 Display Defects	19
Half of the Screen is Not Shown	19
<TABLE>	19
Figure 5-24 Screen display “1/2 display”	19
Vertical Parts of the Screen are Missing	19
Figure 5-25 Screen display “Vertical parts missing”	19
Figure 5-26 Data TCP IC examination	19
Unusual Pattern on Display	19
Figure 5-27 Possible cases	19
Scan FPC Problem	19
Figure 5-28 Screen display “Scan FPC problem”	20
Figure 5-29 Scan IC	20
Vertical Lines with Regular Gap (Vertical Stripe Flash at Special Colour)	20
Figure 5-30 Screen display “Vertical lines with regular gap”	20
Data Copy in Vertical Direction	20
Figure 5-31 Screen display “Data copy in vertical direction”	20
One or Several Vertical Line(s) on the Screen	20
Figure 5-32 Screen display “Vertical lines”	20
One or Several Horizontal Lines on the Screen	20
Figure 5-33 Screen display “Horizontal lines”	20
Low Brightness of Displayed Picture	20
Partially Other Colour on Full White Screen or Partially Mis-Discharge on Full Black Screen.	20
Figure 5-34 Y output voltage waveform	21
No Specified Brightness at Specified Colour	21
5.2.3 Checking for Component Damage	21
Y IPM (IC 18) or Z IPM (IC 2)	21
Figure 5-35 IPM normal output	21
FET assy (Y board: HS2)	21
Figure 5-36 Set_up FET defective	21
Figure 5-37 Set_down FET defective	21
SCAN IC (Y-DRV board: IC1-10)	21
Figure 5-38 SCAN IC defective	22
Figure 5-39 SCAN IC shorted output	22
Figure 5-40 SCAN IC normal output wave	22
TCPs	22
Figure 5-41 COF IC output defective	22
Figure 5-42 TCP normal output	22
Crystal (CTRL board: X1)	22
Figure 5-43 Crystal normal output	23
Figure 5-44 Crystal defective output	23
5.3 Defect Description Form	24
Figure 5-45 Defect Description Form (DDF)	24
6. Block Diagrams, Test Point Overviews, and Waveforms	25
6.1 Block Diagram PDP Module	25
Figure 6-1 Block Diagram	25
7. Circuit Diagrams and PWB Layouts	25
8. Alignments	26
8.1 General	26
8.2 Alignments	26
8.2.1 Tools	26
8.2.2 Connection Diagram and Set-Up	26
Figure 8-1 Measuring equipment connection diagram	26
8.2.3 PSU Alignment	26
Figure 8-2 PSU Alignment	26
Vs Voltage Adjustment	26
Va Voltage Adjustment	27
8.2.4 Y-SUS Alignment	27
Figure 8-3 Y-SUS alignment	27
Condition	27
Vscan Voltage Adjustment	27
-Vy Voltage Adjustment	27
Y -SUS Set-up Voltage Waveform Adjustment	27
Figure 8-4 Trigger point Vs-DA	27
Figure 8-5 V set-up waveform	27
8.2.5 Z-SUS Alignment	28
Figure 8-6 Z-SUS alignment	28
Condition	28
Vzb (Z bias) Voltage Adjustment	28
8.2.6 Internal Test Patterns	28
Figure 8-7 P1: Connector for Internal Test Patterns	28
9. Circuit Descriptions, Abbreviation List, and IC Data Sheets	29
9.1 Introduction	29
9.2 Power Supply Unit (PSU)	29
9.2.1 Purpose	29
Figure 9-1 Power supply	29
9.2.2 Power ON and Power OFF Sequence	30
Figure 9-2 Power supply sequence	30
9.3 Control Board	30
9.3.1 Purpose	30
Figure 9-3 Control board	30
9.4 X Board	30
9.4.1 Purpose	30
Figure 9-4 X boards	30
9.5 Y Sustain Board	31
9.5.1 Purpose	31
Figure 9-5 Y Sustain board	31
9.5.2 Main Components	31
9.6 Y Drive Board	31
9.6.1 Purpose	31
Figure 9-6 Y Drive board	31
9.7 Z Sustain Board	31
9.7.1 Purpose	31
9.7.2 Main Components	31
Figure 9-7 Z Sustain Board	31
9.8 DC/DC Converter Part	32
9.8.1 Purpose	32
Figure 9-8 DC/DC Converter block diagram	32
Figure 9-9 DC/DC Converter part	32
9.9 FPC (Flexible Printed Circuit)	32
9.9.1 Purpose	32
Figure 9-10 Flexible Printed Circuit	32
9.10 FFC (Flat Flexible Cable)	32
9.10.1 Purpose	32
Figure 9-11 Flat Flexible Cable	32
9.11 TCP (Tape Carrier Package)	32
9.11.1 Purpose	32
Figure 9-12 Tape Carrier Package	32
9.12 IPM (Intelligent Power Modules)	33
9.12.1 Purpose	33
Figure 9-13 Intelligent Power Modules	33
9.12.2 Main Components	33
9.13 Abbreviation List	33
9.14 IC Data Sheets	33
10. Spare Parts List	34