Hitachi HTS541680J9SA00 Specifications - Page 21

Operating modes - set up disk

Get Hitachi HTS541680J9SA00 - Travelstar 80 GB Hard Drive PDF manuals and user guides View all Hitachi HTS541680J9SA00 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

4.4.3 Travelstar 5K160 (SATA) Hard Disk Drive Specification Operating modes Operating mode Description Spin-Up Start up time period from spindle stop or power down. Seek Seek operation mode Write Write operation mode Read Read operation mode The device is capable of responding immediately to idle media access requests. All Performance electronic components remain powered and the full frequency servo remains operational. The device is capable of responding immediately to media access requests. Some circuitry-including servo system and R/W electronics-is in power saving mode. Active idle The head is parked near the mid-diameter the disk without servoing. A device in Active idle mode may take longer to complete the execution of a command because it must activate that circuitry. Low power idle The head is unloaded onto the ramp position. The spindle motor is rotating at full speed. The device interface is capable of accepting commands. The spindle motor is Standby stopped. All circuitry but the host interface is in power saving mode. The execution of commands is delayed until the spindle becomes ready. Sleep The device requires a soft reset or a hard reset to be activated. All electronics, including spindle motor and host interface, are shut off. Table 10. Operating mode 4.4.3.1 Mode transition time From To Standby Idle Table 11. Drive ready time Transition Time (typ) 2.5 Transition Time (max.) 9.5 4.4.3.2 Operating mode at power on The device goes into Idle mode after power on or hard reset as an initial state. Initial state may be changed to Standby mode using pin C on the interface connector. Refer to section 7.10 on page 58, "Drive address setting" for details. 4.4.3.3 Adaptive power save control The transient timing from Performance Idle mode to Active Idle mode and Active Idle mode to Low Power Idle mode is controlled adaptively according to the access pattern of the host system. The transient timing from Low Power Idle mode to Standby mode is also controlled adaptively, if it is allowed by Set Features Enable Advanced Power Management subcommand. 21/167

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
Travelstar 5K160 (SATA) Hard Disk Drive Specification
21/167
4.4.3
Operating modes
Operating mode
Description
Spin-Up
Start up time period from spindle stop or power down.
Seek
Seek operation mode
Write
Write operation mode
Read
Read operation mode
Performance
The device is capable of responding immediately to idle media access requests. All
electronic components remain powered and the full frequency servo remains
operational.
Active idle
The device is capable of responding immediately to media access requests. Some
circuitry—including servo system and R/W electronics—is in power saving mode.
The head is parked near the mid-diameter the disk without servoing.
A device in Active idle mode may take longer to complete the execution of a
command because it must activate that circuitry.
Low power idle
The head is unloaded onto the ramp position. The spindle motor is rotating at full
speed.
Standby
The device interface is capable of accepting commands. The spindle motor is
stopped. All circuitry but the host interface is in power saving mode.
The execution of commands is delayed until the spindle becomes ready.
Sleep
The device requires a soft reset or a hard reset to be activated. All electronics,
including spindle motor and host interface, are shut off.
Table 10. Operating mode
4.4.3.1
Mode transition time
From
To
Transition
Time (typ)
Transition Time
(max.)
Standby
Idle
2.5
9.5
Table 11. Drive ready time
4.4.3.2
Operating mode at power on
The device goes into Idle mode after power on or hard reset as an initial state. Initial state may be
changed to Standby mode using pin C on the interface connector. Refer to section 7.10 on page 58,
"Drive address setting" for details.
4.4.3.3
Adaptive power save control
The transient timing from Performance Idle mode to Active Idle mode and Active Idle mode to Low Power
Idle mode is controlled adaptively according to the access pattern of the host system.
The transient
timing from Low Power Idle mode to Standby mode is also controlled adaptively, if it is allowed by Set
Features Enable Advanced Power Management subcommand.