Hoover UH30065 Manual - Page 7

Using the cleaner - carpet cleaner

Get Hoover UH30065 PDF manuals and user guides View all Hoover UH30065 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Using the cleaner DO NOT USE CLEANER OUTDOORS OR ON DAMP OR WET SURFACES. POWER button Surface Command™ control dial (some models) ® Surface Selector (some models) A 9 The POWER button (A) is located at the top of the cleaner body. Plug cord into electrical outlet. To turn cleaner ON, press button once. To turn cleaner OFF, press button again. NOTE: THE CLEANER IS SHIPPED WITH THE CONTROL DIAL IN HARD FLOOR POSITION. BEFORE YOU BEGIN TO CLEAN CARPETS, ROTATE THE CONTROL DIAL FROM HARD FLOOR TO A CARPET SETTING. 10 The Surface Command™ control dial (some models) is an automat- ic height adjustment that allows you to choose a cleaning mode for carpet height or hard surface floors. For maximum cleaning performance, the following carpet height settings are recommended: Lowest setting: for all types of carpet, Note: If the cleaner is difficult to push, turn dial to the next higher setting. Higher settings: for very deep pile carpet where easier pushing effort is desired, while maintaining good cleaning performance. HARD FLOOR The agitator brush roll is OFF; the nozzle is set at LOW. 11 The Surface Selector (some models) has three carpet height settings and a hard floor setting. The Surface Selector turns to allow you to choose a cleaning mode for carpet height or hard surface floors. For maximum cleaning performance, the following carpet height settings are recommended: Lowest setting: for all types of carpet, Note: If the cleaner is difficult to push, turn dial to the next higher setting. Higher settings: for very deep pile carpet where easier pushing effort is desired, while maintaining good cleaning performance. HARD FLOOR MODE (with agitator brush roll shut off) the nozzle is set at LOW. Automatic agitator brush roll shut-off Agitator brush roll control Cord rewind B A OR A A B 12 The agitator brush roll will turn off when the handle is in the upright, storage position. 13 Rotate control dial to "Carpet" settings (A) to turn agitator brush roll ON for cleaning carpet or rugs. Rotate control dial to "Hard Floor" (B) to turn agitator brush roll OFF when cleaning hard floors. 14 Grasp the end of the plug and pull to release cord from cord reel. After desired cord length is reached, the cord will lock into position. (Cont'd) ¡ 07

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
®
DO NOT USE CLEANER OUTDOORS
OR ON DAMP
OR WET SURF
ACES.
POWER button
The POWER button (A) is located
at the top of the cleaner body.
Plug cord into electrical outlet.
To turn cleaner
ON
, press button once.
To turn cleaner
OFF
, press button again.
9
A
B
B
A
Using the cleaner
The Surface Command™ control
dial (some models) is an automat-
ic height adjustment that allows you to
choose a cleaning mode for carpet
height or hard surface floors.
For maximum cleaning performance,
the following carpet height settings are
recommended:
Lowest setting:
for all types of carpet,
Note:
If the cleaner is difficult to push,
turn dial to the next higher setting.
Higher settings:
for very deep pile car-
pet where easier pushing effort is
desired, while maintaining good clean-
ing performance.
HARD FLOOR
The agitator brush roll is
OFF
; the nozzle is set at
LOW
.
Surface Command™
control dial (some models)
Surface Selector (some
models)
Automatic agitator
brush roll shut-off
Agitator brush roll control
Cord rewind
10
The agitator brush roll will turn off
when the handle is in the upright,
storage position.
12
Rotate control dial to “Carpet”
settings (A) to turn agitator brush
roll ON for cleaning carpet or rugs.
Rotate control dial to “Hard Floor” (B) to
turn agitator brush roll OFF when clean-
ing hard floors.
13
(Cont’d)
→
The Surface Selector (some
models) has three carpet
height
settings and a hard floor setting. The
Surface Selector turns to allow you to
choose a cleaning mode for carpet
height or hard surface floors.
For maximum cleaning performance, the
following carpet height settings are rec-
ommended:
Lowest setting:
for all types of carpet,
Note:
If the cleaner is difficult to push,
turn dial to the next higher setting.
Higher settings:
for very deep pile car-
pet where easier pushing effort is
desired, while maintaining good clean-
ing performance.
HARD FLOOR MODE
(with agitator
brush roll shut off) the nozzle is set at
LOW
.
11
07
A
A
OR
Grasp the end of the plug and
pull to release cord from cord
reel. After desired cord length is reached,
the cord will lock into position.
14
NOTE:
THE CLEANER IS SHIPPED
WITH THE CONTROL DIAL IN HARD
FLOOR POSITION.
BEFORE YOU
BEGIN TO CLEAN CARPETS,
RO
T
A
TE
THE CONTROL DIAL FROM HARD
FLOOR
T
O
A C
ARPET SETTING.