Husqvarna AUTOMOWER 430XH Owner Manual - Page 40

Introduction - troubleshooting, 2 Fault messages

Page 40 highlights

6 Troubleshooting 6.1 Introduction - troubleshooting In this chapter, a number of messages are listed which may be shown in the display if there is a malfunction. There is a proposal as to the cause and steps to take for each message. This chapter also presents some symptoms that can guide you if the product does not work as expected. More suggestions for steps to take in the event of malfunction or symptoms can be found on www.husqvarna.com. 6.2 Fault messages The list below shows a number of fault messages that may be shown in the display of the product. Contact your local Husqvarna representative if the same message appears often. Message Wheel motor blocked Cutting system blocked Cutting height blocked Trapped Cause Action Grass or other object is wrapped around the drive wheel. Check the drive wheel and remove the grass or other object. Grass or other object is wrapped around the blade disc. Check the drive wheel and remove the grass or other object. The blade disc lies in a pool of water. Move the product and prevent the collection of water in the work area. Grass or other object is wrapped around the cutting height adjustment, or between the blade disc and chassis. Check the blade disc and the bellows around the cutting height adjustment, and remove any grass or other objects that may have got stuck. The product has got caught in something. Free the product and rectify the reason for it becoming trapped. The product is stuck behind a number of obstacles. Check if there are any obstacles which make it hard for the product to move on from this location. 40 - Troubleshooting 1230 - 001 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

6 Troubleshooting
6.1 Introduction - troubleshooting
In this chapter, a number of messages are listed which may be shown in the display if there is a
malfunction. There is a proposal as to the cause and steps to take for each message. This chapter also
presents some symptoms that can guide you if the product does not work as expected. More
suggestions for steps to take in the event of malfunction or symptoms can be found on
www.husqvarna.com.
6.2 Fault messages
The list below shows a number of fault messages that may be shown in the display of the product.
Contact your local Husqvarna representative if the same message appears often.
Message
Cause
Action
Wheel motor
blocked
Grass or other object is wrapped
around the drive wheel.
Check the drive wheel and remove the
grass or other object.
Cutting system
blocked
Grass or other object is wrapped
around the blade disc.
Check the drive wheel and remove the
grass or other object.
The blade disc lies in a pool of water.
Move the product and prevent the col-
lection of water in the work area.
Cutting height
blocked
Grass or other object is wrapped
around the cutting height adjustment,
or between the blade disc and chassis.
Check the blade disc and the bellows
around the cutting height adjustment,
and remove any grass or other objects
that may have got stuck.
Trapped
The product has got caught in some-
thing.
Free the product and rectify the reason
for it becoming trapped.
The product is stuck behind a number
of obstacles.
Check if there are any obstacles which
make it hard for the product to move on
from this location.
40
- Troubleshooting
1230 - 001 -