Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 430XH » Manual Viewer

Husqvarna AUTOMOWER 430XH Owner Manual - Page 50

Finding breaks in the loop wire

View all Husqvarna AUTOMOWER 430XH manuals

Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Symptoms Cause Action The product often Spiral cutting is a natural part of the moves in circles or product's movement patter. spirals. Adjust the intensity of spiral cutting. This function can be disabled if necessary. Refer to Spiral Cutting on page 31. The product turns This is completely normal for the prodround and stays uct. The product have GPS assisted on a small area for navigation that contributes to an even several minutes. result. No action. Uneven mowing results. The product works too few hours per day. The How often? setting is incorrect in relation to the layout of the work area. Note: Not applicable if GPS assisted navigation is enabled. The shape of the work area requires the use of Area 1-5 for the product to find its way to all remote areas. Note: Not applicable if GPS assisted navigation is enabled. Increase the mowing time. Refer to To do the timer settings on page 24. The Weather timer senses that the lawn has been mowed more than it actually has. Increase the intensity level in the Weather timer. Disable the Weather timer if this does not help. Check that the correct How often? value is selected. Use Area 1-5 to steer the product to a remote area. Refer to Lawn coverage on page 27. Work area is too large. Try to limit the work area, or to extend the work time. Refer to To do the timer settings on page 24. Dull blades. Replace all the blades. Refer to Replace the blades on page 38. Long grass in relation to the set cutting Increase the cutting height and then height. successively lower it. Accumulation of grass by the blade disc or around the motor shaft. Check that the blade disc rotates freely and easily. If not, screw off the blade disc and remove grass and foreign objects. Refer to Clean the product on page 37. 6.7 Finding breaks in the loop wire Breaks in the loop wire are usually the result of unintentional physical damage to the wire such as when gardening with a shovel. In countries with ground frost, also sharp stones that move in the ground can damage the wire. Breaks can also occur due to the wire being stretched excessively during installation. Mowing the grass too low right after the installation can damage wire insulation. Damage to the insulation may not cause disruptions until several weeks or months later. 50 - Troubleshooting 1230 - 001 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	12
Safety instructions for operation	13
Use	13
Battery safety	14
How to lift and move the product	14
Maintenance	15
In the event of a thunderstorm	15
Installation	16
Introduction - Installation	16
Before the installation of the wires	16
Before the installation of the product	16
To examine where to put the charging station	16
To examine where to put the power supply	17
To examine where to put the boundary wire	17
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	21
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	22
To extend the boundary wire or the guide wire	22
After the installation of the product	22
To do a visual check of the charging station	22
To do the basic settings	23
Automower® Connect app	23
To install the Automower® Connect app	23
Automower® Connect menu	23
Dashboard	23
Map	24
Settings in Automower® Connect	24
To do the product settings	24
To get access to the menu	24
To do the timer settings	24
To calculate the timer setting	24
To set the timer	24
To copy the timer setting	24
To reset the timer setting	25
Cutting height	25
To set the cutting height	25
Security level	25
To set the security level	25
To change the PIN-code	26
To create a New loop signal	26
To set duration of alarm and time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	27
Installation	27
Lawn coverage	27
To disable and enable the GPS function	27
To set the Lawn coverage function	27
To do a test of the Lawn coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn coverage function	28
Finding the charging station	28
To set the delay time for the guide wire and the boundary wire	29
To disable the guide wire and boundary wire	29
To test if the product can find the charging station	29
To reset the settings for the guide wire and the boundary wire	29
To change the signal range of the charging station	29
Advanced	29
Corridor width	29
To set the corridor width	29
Exit angles	30
To set the exit angles	30
To set the reversing distance	30
To set the Drive Past Wire function	30
Settings	30
Profiles	30
To save settings to a profile	30
To use a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the level of Spiral Cutting	31
Slope Control	31
To enable or disable the Slope control	31
General	31
To set the time & date	31
To set the language	32
To set the Country & Timezone	32
To reset all user settings	32
The About menu	32
Accessories	32
Information	32
Automower® Connect	32
To pair Automower® Connect and the product	32
To set the Geofence level of sensitivity	32
To use the SMS function	32
Network	33
SIM PIN	33
APN settings	33
To reset the Automower® Connect settings	33
Headlights	33
To set the schedule for the headlights	33
To set the Flashes when fault function	33
Ultrasonic (Automower® 450XH)	33
To set the Ultrasonic function	33
Mower house	33
To avoid collisions with the mower house	33
Operation	34
Main switch	34
To start the product	34
Operating mode - Start	34
Main area	34
Override timer	34
Secondary area	34
Spot cutting	35
Operating mode - Park	35
Park until further notice	35
Start again in 3 hours	35
Start with next timer	35
To stop the product	35
To switch off the product	35
To charge the battery	35
Maintenance	37
Introduction - maintenance	37
Clean the product	37
Chassis and blade disc	37
Chassis	37
Wheels	37
Cover	37
Charging station	37
Replace the blades	38
To replace the blades	38
Battery	38
Winter service	39
Troubleshooting	40
Introduction - troubleshooting	40
Fault messages	40
Information messages	45
LED indicator lamp on the charging station	47
LED indicator lamp on the product	48
Symptoms	49
Finding breaks in the loop wire	50
Transportation, storage and disposal	53
Transportation	53
Storage	53
Disposal	53
To remove the battery	53
Technical data	54
Technical data	54
Warranty	57
Warranty terms	57
Applicable to US/CA market	58
Supplier's Declaration of Conformity	58

Match case Limit results 1 per page

Symptoms

Cause

Action

The product often

moves in circles or

spirals.

Spiral cutting is a natural part of the

product's movement patter.

Adjust the intensity of spiral cutting.

This function can be disabled if neces-

sary. Refer to

Spiral Cutting on page

The product turns

round and stays

on a small area for

several minutes.

This is completely normal for the prod-

uct. The product have GPS assisted

navigation that contributes to an even

result.

No action.

Uneven mowing

results.

The product works too few hours per

day.

Increase the mowing time. Refer to

do the timer settings on page 24

The

Weather timer

senses that the

lawn has been mowed more than it ac-

tually has. Increase the intensity level

in the

Weather timer

. Disable the

Weather timer

if this does not help.

The

How often?

setting is incorrect in

relation to the layout of the work area.

Note:

Not applicable if GPS assisted

navigation is enabled.

Check that the correct

How often?

val-

ue is selected.

The shape of the work area requires

the use of

Area 1-5

for the product to

find its way to all remote areas.

Note:

Not applicable if GPS assisted naviga-

tion is enabled.

Use

Area 1-5

to steer the product to a

remote area. Refer to

Lawn coverage

on page 27

Work area is too large.

Try to limit the work area, or to extend

the work time. Refer to

To do the timer

settings on page 24

Dull blades.

Replace all the blades. Refer to

Re-

place the blades on page 38

Long grass in relation to the set cutting

height.

Increase the cutting height and then

successively lower it.

Accumulation of grass by the blade

disc or around the motor shaft.

Check that the blade disc rotates freely

and easily. If not, screw off the blade

disc and remove grass and foreign ob-

jects. Refer to

Clean the product on

page 37

6.7 Finding breaks in the loop wire

Breaks in the loop wire are usually the result of

unintentional physical damage to the wire such

as when gardening with a shovel. In countries

with ground frost, also sharp stones that move in

the ground can damage the wire. Breaks can

also occur due to the wire being stretched

excessively during installation.

Mowing the grass too low right after the

installation can damage wire insulation. Damage

to the insulation may not cause disruptions until

several weeks or months later.

- Troubleshooting

1230 - 001 -