Husqvarna L321AHE Owner Manual - Page 22
Collecteur d'herbe, Poignée du lanceur, Engine
View all Husqvarna L321AHE manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
MAINTENANCE Gear cases • To keep your drive system working properly, the gear cases and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season. • The gear cases are filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case. • Under normal usage the grass catcher is subject to deterioration and wear. Check the grass catcher frequently for wear or deterioration. Replace the bag only with grass bags that meet the manufacturer's recommendations and specifications. Water washout feature Your lawn mower is equipped with a fitting that allows quick and easy cleaning of the underside of the housing. Note that water, grass and other debris will drain from beneath the mower housing during the washout process. 1 Move the machine to an area of cut grass or another hard surface. 2 Remove grass catcher or mulch plug from the lawn mower. 3 Close the back shield. 4 Connect a garden hose to the washout port fitting. Engine Lubrication Use only high quality detergent oil rated with API service classification SG-SL. Select the oil's SAE viscosity grade according to your expected operating temperature. SSAAEE VVISCOSITY GGRRAADDEESS 5W-30 SAE 30 F -20 0 30 32 40 60 80 100 C -30 -20 -10 0 10 20 30 40 TTEEMMPPEERRAATTUURREERRAANNGGEE AANNTICIPATED BBEEFFOORREENNEEXXTTOOILILCCHHAANNGGEE CAUTION! Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F / 0°C. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. • Change the oil after every 25 hours of operation or at least once a year. • Check the engine oil level before starting the engine and after each 5 hours of continuous use. Tighten oil plug securely each time you check the oil level. Oil level Before starting for the first time Your lawnmower is shipped without oil in the engine. You receive a container of oil with the unit. Slowly pour the entire container down the oil fill spout into the engine. IMPORTANT! Do not overfill! Check the engine's oil level The lawn mower should stand on flat ground when you check the oil level. Ensure the ignition lead has been removed from the spark plug before you open the oil filler cap. 1 Check the oil level with the dipstick on the oil filler cap. 5 Turn on water supply and check for leaks at the fitting. 6 If no leaks are present, start engine and let engine run until the underside of the lawn mower is clean. 2 Remove the oil cap and wipe the dipstick clean. 3 Put the dipstick back in. The oil filler cap must be completely screwed down to give a correct picture of the oil level. CAUTION! Do not engage the drive system during the washout process. 7 Turn off the engine. 8 Shut off water supply and remove hose from fitting. IMPORTANT! Do not remove hose from fitting while engine is running. Water in engine can result in shortened engine life. 9 Start engine and let engine run for a full minute to remove excess water from mower. 22 - English MONTAGE ET RÉGLAGES Entreposage avec poignée verticale La poignée peut être réglée dans une position de rangement verticale. 1 Desserrer les boutons de la poignée inférieure. 2 Faire pivoter le guidon et aligner les goupilles avec la fente verticale du support. Collecteur d'herbe Montage du collecteur d'herbe 1 Mettre le châssis du collecteur d'herbe dans le sac à herbe en orientant la partie rigide du sac vers le bas. S'assurer que la poignée du châssis se trouve à l'extérieur de la partie supérieure du sac. 2 Fixer le sac à herbe sur le châssis au moyen des attaches à fixation rapide. 3 Resserrer les boutons. Position de transport et d'entreposage On peut replier la poignée pour réduire l'espace nécessaire pour le transport et l'entreposage. MISE EN GARDE! Prendre soin de ne pas endommager les câbles et les fils électriques lors du pliage du guidon. 1 Desserrer les deux boutons de la poignée supérieure et laisser la poignée s'abaisser vers l'arrière. 2 Desserrer les deux boutons de la poignée inférieure, faire pivoter l'ensemble de la poignée vers l'avant et la laisser reposer sur la tondeuse. Poignée du lanceur Installer la poignée du lanceur 1 Desserrer le bouton de verrouillage. 2 Maintenir la poignée de frein moteur contre la poignée supérieure. 3 Saisir la poignée du lanceur, tirer doucement la poignée du lanceur du moteur jusqu'à ce que la corde du lanceur puisse glisser dans la boucle de la corde guide. 4 Serrer le bouton de verrouillage. French - 67