IBM 4910-33D Installation Guide - Page 25

Removal and installation procedures for the 4810/4910 SurePOS 300

Get IBM 4910-33D PDF manuals and user guides View all IBM 4910-33D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

March 2009 Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300 This section describes how to remove and install the components of Model x4x of the 4810/4910 SurePOS 300. These are the procedures that are included: v "Removing and installing the top cover" on page 12 v "Removing and installing the hard disk drive" on page 14 v "Removing and installing the hard disk drive and hard disk tray as an assembly" on page 15 v "Removing and installing the flash drive" on page 16 v "Removing and installing the memory module" on page 17 v "Removing and installing the front-panel card" on page 18 v "Removing and installing the I/O connector card" on page 19 v "Removing and installing the riser card and the I/O connector card as an assembly" on page 20 v "Resetting the system board CMOS settings" on page 23 v "Removing and installing the power supply" on page 21 v "Removing and installing the hard disk drive air duct" on page 22 v "Removing and installing the battery" on page 23 v "Removing and installing the system board" on page 25 v "Removing and installing the front cover" on page 27 © Copyright IBM Corp. 2005, 2009 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Chapter 3. Removal and installation procedures for the
4810/4910 SurePOS 300
This section describes how to remove and install the components of Model x4x of
the 4810/4910 SurePOS 300. These are the procedures that are included:
v
“Removing and installing the top cover” on page 12
v
“Removing and installing the hard disk drive” on page 14
v
“Removing and installing the hard disk drive and hard disk tray as an assembly”
on page 15
v
“Removing and installing the flash drive” on page 16
v
“Removing and installing the memory module” on page 17
v
“Removing and installing the front-panel card” on page 18
v
“Removing and installing the I/O connector card” on page 19
v
“Removing and installing the riser card and the I/O connector card as an
assembly” on page 20
v
“Resetting the system board CMOS settings” on page 23
v
“Removing and installing the power supply” on page 21
v
“Removing and installing the hard disk drive air duct” on page 22
v
“Removing and installing the battery” on page 23
v
“Removing and installing the system board” on page 25
v
“Removing and installing the front cover” on page 27
March 2009
© Copyright IBM Corp. 2005, 2009
11