IBM 4910-33D Installation Guide - Page 31

Removing and installing the memory module, See

Get IBM 4910-33D PDF manuals and user guides View all IBM 4910-33D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

March 2009 Removing and installing the memory module 2 Figure 10. Opening the memory-module retainer clips 1 Figure 11. Memory-module retainer clips in the open position. To remove the memory module: 1. Open the unit. See "Removing and installing the top cover" on page 12. 2. Remove the hard drive and tray assembly. See "Removing and installing the hard disk drive and hard disk tray as an assembly" on page 15 3. Rotate the memory-module-retainer clips 1 to the open position. The memory module is disengaged from the memory connector. See Figure 11. 4. Lift the memory module 2 straight up to remove it from the memory connector. See Figure 11. 1 2 Figure 12. Installing the memory module Figure 13. Closing the memory-module retainer clips To install the memory module: 1. Position the replacement memory module 1 over the memory connector. Be sure the notch on the memory module aligns correctly with the connector key 2 on the memory connector. See Figure 12. 2. Align the memory module with the memory socket and push down engaging the memory-module retainer clips; push down firmly to engage. Note: Be sure the memory-module retainer clips are fully closed. See Figure 13. 3. Replace the hard drive and tray assembly. See "Removing and installing the hard disk drive and hard disk tray as an assembly" on page 15. 4. Replace the top cover. See "Removing and installing the top cover" on page 12. Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removing and installing the memory module
Figure 10. Opening the memory-module
retainer clips
2
1
Figure 11. Memory-module retainer clips in
the open position.
To remove the memory module:
1.
Open the unit. See “Removing and installing the top cover” on page 12.
2.
Remove the hard drive and tray assembly. See “Removing and installing the
hard disk drive and hard disk tray as an assembly” on page 15
3.
Rotate the memory-module-retainer clips
±1²
to the open position. The memory
module is disengaged from the memory connector. See Figure 11.
4.
Lift the memory module
±2²
straight up to remove it from the memory connector.
See Figure 11.
1
2
Figure 12. Installing the memory module
Figure 13. Closing the memory-module
retainer clips
To install the memory module:
1.
Position the replacement memory module
±1²
over the memory connector. Be
sure the notch on the memory module aligns correctly with the connector
key
±2²
on the memory connector. See Figure 12.
2.
Align the memory module with the memory socket and push down engaging the
memory-module retainer clips; push down firmly to engage.
Note:
Be sure the memory-module retainer clips are fully closed. See
Figure 13.
3.
Replace the hard drive and tray assembly. See “Removing and installing the
hard disk drive and hard disk tray as an assembly” on page 15.
4.
Replace the top cover. See “Removing and installing the top cover” on page 12.
March 2009
Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300
17