IBM 4910-33D Installation Guide - Page 28

Removing and installing the hard disk drive, Grasp the hard drive on each side

Get IBM 4910-33D PDF manuals and user guides View all IBM 4910-33D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

March 2009 Removing and installing the hard disk drive This section describes how to remove, install and replace the hard drive unit. To remove the hard drive and the hard drive tray as an assembly, see "Removing and installing the hard disk drive and hard disk tray as an assembly" on page 15. Note: The hard drive assembly might not be installed on a unit where the modular flash drive is installed instead. 1 2 2 Figure 7. Removing the hard disk drive To remove the hard disk drive: 1. Open the unit. See "Removing and installing the top cover" on page 12. 2. Rotate the hard drive retainer 1 to the fully open position as shown by the arrow in the figure. 3. Grasp the hard drive on each side 2 and lift it up and out of the system unit. To install the hard disk drive: 1. When replacing the hard drive into the hard drive tray, the hard drive connectors face the front of the system unit. Ensure that the hard drive is firmly in place. 2. Replace the cover. See "Removing and installing the top cover" on page 12. 14 SurePOS Installation and Service

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removing and installing the hard disk drive
This section describes how to remove, install and replace the hard drive unit. To
remove the hard drive and the hard drive tray as an assembly, see “Removing and
installing the hard disk drive and hard disk tray as an assembly” on page 15.
Note:
The hard drive assembly might not be installed on a unit where the modular
flash drive is installed instead.
To remove the hard disk drive:
1.
Open the unit. See “Removing and installing the top cover” on page 12.
2.
Rotate the hard drive retainer
±1²
to the fully open position as shown by the
arrow in the figure.
3.
Grasp the hard drive on each side
±2²
and lift it up and out of the system unit.
To install the hard disk drive:
1.
When replacing the hard drive into the hard drive tray, the hard drive connectors
face the front of the system unit. Ensure that the hard drive is firmly in place.
2.
Replace the cover. See “Removing and installing the top cover” on page 12.
1
2
2
Figure 7. Removing the hard disk drive
March 2009
14
SurePOS Installation and Service