IBM 4910-33D Installation Guide - Page 29

Removing and installing the hard disk drive and hard disk tray as an assembly

Get IBM 4910-33D PDF manuals and user guides View all IBM 4910-33D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

March 2009 Removing and installing the hard disk drive and hard disk tray as an assembly 1 3 3 2 2 3 Figure 8. Removing the hard drive and hard drive tray as an assembly To remove the hard drive and tray as an assembly: v Open the unit. See "Removing and installing the top cover" on page 12. v Grasp the tray assembly 1 where the arrows originate 2 . v Pull the tray assembly in an upward direction as shown by the arrows; this will disengage the tray assembly retainers. To install the hard drive and tray as an assembly: 1. Align the hard drive tray with the three alignment features 3 . Move the hard drive tray down and over the alignment features 3 and snap into place. 2. Ensure that the hard drive is completely seated on the alignment pins and the front of the tray is correctly positioned in the slots on the chassis. 3. Replace the cover. See "Removing and installing the top cover" on page 12. Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removing and installing the hard disk drive and hard disk tray as an
assembly
To remove the hard drive and tray as an assembly:
v
Open the unit. See “Removing and installing the top cover” on page 12.
v
Grasp the tray assembly
±1²
where the arrows originate
±2²
.
v
Pull the tray assembly in an upward direction as shown by the arrows; this will
disengage the tray assembly retainers.
To install the hard drive and tray as an assembly:
1.
Align the hard drive tray with the three alignment features
±3²
. Move the hard
drive tray down and over the alignment features
±3²
and snap into place.
2.
Ensure that the hard drive is completely seated on the alignment pins and the
front of the tray is correctly positioned in the slots on the chassis.
3.
Replace the cover. See “Removing and installing the top cover” on page 12.
2
3
2
1
3
3
Figure 8. Removing the hard drive and hard drive tray as an assembly
March 2009
Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300
15