IBM 4910-33D Installation Guide - Page 41

Removing and installing the front cover, to separate the front cover from the chassis.

Get IBM 4910-33D PDF manuals and user guides View all IBM 4910-33D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

March 2009 Removing and installing the front cover 1 3 2 Figure 23. Removing the front cover To remove the front cover: 1. Open the unit. See "Removing and installing the top cover" on page 12. 2. Remove the hard drive assembly. See "Removing and installing the hard disk drive and hard disk tray as an assembly" on page 15. 3. Release the bottom two retaining tabs 2 one at a time, applying pressure to separate the front cover from the chassis. 4. Release the top three retaining tabs 1 one at a time, and slide the cover to the right 3 to separate the front cover from the chassis. 5. Unsnap the sixth retaining tab as you move the front cover toward the right 3 . To install the front panel: 1. Align all five of the front panel retainers. 2. Push the front panel toward the chassis and snap into position. Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
Removing and installing the front cover
To remove the front cover:
1.
Open the unit. See “Removing and installing the top cover” on page 12.
2.
Remove the hard drive assembly. See “Removing and installing the hard disk
drive and hard disk tray as an assembly” on page 15.
3.
Release the bottom two retaining tabs
±2²
one at a time, applying pressure to
separate the front cover from the chassis.
4.
Release the top three retaining tabs
±1²
one at a time, and slide the cover to the
right
±3²
to separate the front cover from the chassis.
5.
Unsnap the sixth retaining tab as you move the front cover toward the right
±3²
.
To install the front panel:
1.
Align all five of the front panel retainers.
2.
Push the front panel toward the chassis and snap into position.
2
1
3
Figure 23. Removing the front cover
March 2009
Chapter 3. Removal and installation procedures for the 4810/4910 SurePOS 300
27