IBM 6648 User Guide - Page 54

ACPI BIOS IRQ, ACPI Standby Mode, Setting power-management features, Important, Time to Low Power

Get IBM 6648 - NetVista A40 - 128 MB RAM PDF manuals and user guides
UPC - 087944583387
View all IBM 6648 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

ACPI BIOS IRQ Automatic Configuration and Power Interface (ACPI) BIOS IRQ enables the operating system to control the power-management features of your computer. You can use the ACPI BIOS IRQ setting to configure the interrupts that this feature uses so that you can free resources for other devices. Not all operating systems support ACPI BIOS IRQ. See your operating system documentation to determine if ACPI is supported. ACPI Standby Mode Some models might allow you to select the power level to which the computer will go when entering standby mode. These models allow you to select standby mode S1 or S3. When the computer enters S1 mode, power is maintained to all devices, but microprocessor activity is halted. When the computer enters S3 mode, power is maintained only for main memory. Some computers do not support S3 mode. If the Standby Mode setting the Configuration/Setup Utility program does not allow you to select S3, your computer only supports Standby Mode S1. If the Standby Mode setting in the Configuration/Setup Utility program allows you to select S3, be sure to read the following important information. Important Some adapters might not wake up properly from Standby Mode S3. If your computer appears to have stopped and will not wake up from stanby, press and hold the power switch for 5 seconds. Your computer will exit standby mode and turn off. Press the power switch to turn the computer back on. If you encounter a problem with Standby Mode S3, set this option to S1 and check to see if updated device drivers that support Standby Mode S3 are available for your adapters. Setting power-management features With power management, the computer and monitor (if the monitor supports DPMS) can be set to go into a reduced power state if they are inactive for a specified length of time. v Time to Low Power: When you enable Automatic Hardware Power Management, you can use this option to specify the amount of time that the computer must be inactive before power-management features are activated. v System Power: You can select ON if you want the computer to remain on or OFF if you want the computer to shut down. v Display: You can use this option to select one of the following reduced-power states: 40 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
ACPI BIOS IRQ
Automatic Configuration and Power Interface (ACPI) BIOS IRQ enables the
operating system to control the power-management features of your computer.
You can use the ACPI BIOS IRQ setting to configure the interrupts that this
feature uses so that you can free resources for other devices. Not all operating
systems support ACPI BIOS IRQ. See your operating system documentation to
determine if ACPI is supported.
ACPI Standby Mode
Some models might allow you to select the power level to which the computer
will go when entering standby mode. These models allow you to select
standby mode S1 or S3.
When the computer enters S1 mode, power is maintained to all devices, but
microprocessor activity is halted.
When the computer enters S3 mode, power is maintained only for main
memory. Some computers do not support S3 mode. If the Standby Mode
setting the Configuration/Setup Utility program does not allow you to select
S3, your computer only supports Standby Mode S1. If the Standby Mode
setting in the Configuration/Setup Utility program allows you to select S3, be
sure to read the following important information.
Important
Some adapters might not wake up properly from Standby Mode S3. If
your computer appears to have stopped and will not wake up from
stanby, press and hold the power switch for 5 seconds. Your computer
will exit standby mode and turn off. Press the power switch to turn the
computer back on.
If you encounter a problem with Standby Mode S3, set this option to S1
and check to see if updated device drivers that support Standby Mode S3
are available for your adapters.
Setting power-management features
With power management, the computer and monitor (if the monitor supports
DPMS) can be set to go into a reduced power state if they are inactive for a
specified length of time.
v
Time to Low Power:
When you enable
Automatic Hardware Power
Management
, you can use this option to specify the amount of time that the
computer must be inactive before power-management features are activated.
v
System Power:
You can select
ON
if you want the computer to remain on or
OFF
if you want the computer to shut down.
v
Display:
You can use this option to select one of the following
reduced-power states:
40
User Guide