IBM 72335LU User Guide - Page 44

Installing, hot-swap, drive - m2 serverproven

Get IBM 72335LU - System x3850 M2 PDF manuals and user guides
UPC - 883436081535
View all IBM 72335LU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Attention: When you install an adapter, avoid touching the components and gold-edge connectors on the adapter. Make sure that the adapter is correctly seated in the connector. Incorrectly seated adapters might cause damage to the I/O board or to the adapter. 8. Touch the static-protective package that contains the adapter to any unpainted surface on the outside of the server; then, grasp the adapter by the top edge or upper corners of the adapter and remove it from the package. 9. Carefully grasp the adapter by its top edge or upper corners, and align it with the connector on the I/O board. 10. Press the adapter firmly into the adapter connector. 11. Optionally, if you are installing the adapter in slot 1 through slot 5, install an expansion-slot screw to secure the adapter. Note: The expansion-slot screws are on the adapter-retention bracket. 12. If you are installing the adapter in slot 6 or slot 7, close the tab; then, push down on the orange adapter retention latch until it clicks into place, securing the adapter. 13. Rotate the adapter-retention bracket to the closed position. 14. If you are installing a low-profile adapter, install a ratchet pin in the adapter-retention bracket to secure the adapter. Press the ratchet pin until it touches the top edge of the adapter. Retention pin Adapter-retention bracket Removal button Note: Press the removal button and pull up on the ratchet pin to remove the ratchet pin from the adapter-retention bracket. 15. Connect any required cables to the adapter. If you have other devices to install or remove, do so now. Otherwise, go to "Completing the installation" on page 50. Installing a hot-swap hard disk drive The following notes describe the types of hard disk drives that the server supports and other information that you must consider when you install a hard disk drive: v The server supports up to four 1-inch (26 mm) slim-high, 2.5-inch, hot-swap hard disk drives in the standard hot-swap bays. v For a list of supported optional devices for the server, see http://www.ibm.com/ servers/eserver/serverproven/compat/us/. v Inspect the drive tray for signs of damage. v Make sure that the drive is correctly installed in the tray. 32 IBM System x3850 M2 and System x3950 M2 Type 7141: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Attention:
When
you
install
an
adapter,
avoid
touching
the
components
and
gold-edge
connectors
on
the
adapter.
Make
sure
that
the
adapter
is
correctly
seated
in
the
connector.
Incorrectly
seated
adapters
might
cause
damage
to
the
I/O
board
or
to
the
adapter.
8.
Touch
the
static-protective
package
that
contains
the
adapter
to
any
unpainted
surface
on
the
outside
of
the
server;
then,
grasp
the
adapter
by
the
top
edge
or
upper
corners
of
the
adapter
and
remove
it
from
the
package.
9.
Carefully
grasp
the
adapter
by
its
top
edge
or
upper
corners,
and
align
it
with
the
connector
on
the
I/O
board.
10.
Press
the
adapter
firmly
into
the
adapter
connector.
11.
Optionally,
if
you
are
installing
the
adapter
in
slot
1
through
slot
5,
install
an
expansion-slot
screw
to
secure
the
adapter.
Note:
The
expansion-slot
screws
are
on
the
adapter-retention
bracket.
12.
If
you
are
installing
the
adapter
in
slot
6
or
slot
7,
close
the
tab;
then,
push
down
on
the
orange
adapter
retention
latch
until
it
clicks
into
place,
securing
the
adapter.
13.
Rotate
the
adapter-retention
bracket
to
the
closed
position.
14.
If
you
are
installing
a
low-profile
adapter,
install
a
ratchet
pin
in
the
adapter-retention
bracket
to
secure
the
adapter.
Press
the
ratchet
pin
until
it
touches
the
top
edge
of
the
adapter.
Retention pin
Removal button
Adapter-retention
bracket
Note:
Press
the
removal
button
and
pull
up
on
the
ratchet
pin
to
remove
the
ratchet
pin
from
the
adapter-retention
bracket.
15.
Connect
any
required
cables
to
the
adapter.
If
you
have
other
devices
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
50.
Installing
a
hot-swap
hard
disk
drive
The
following
notes
describe
the
types
of
hard
disk
drives
that
the
server
supports
and
other
information
that
you
must
consider
when
you
install
a
hard
disk
drive:
v
The
server
supports
up
to
four
1-inch
(26
mm)
slim-high,
2.5-inch,
hot-swap
hard
disk
drives
in
the
standard
hot-swap
bays.
v
For
a
list
of
supported
optional
devices
for
the
server,
see
servers/eserver/serverproven/compat/us/.
v
Inspect
the
drive
tray
for
signs
of
damage.
v
Make
sure
that
the
drive
is
correctly
installed
in
the
tray.
32
IBM
System
x3850
M2
and
System
x3950
M2
Type
7141:
User’s
Guide