IBM 72335LU User Guide - Page 62

Completing, installation

Get IBM 72335LU - System x3850 M2 PDF manuals and user guides
UPC - 883436081535
View all IBM 72335LU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Alignment indicator VRM cradle 15. Install a VRM in the connector next to the microprocessor socket: a. Turn the VRM so that the keys align with the slot. b. Insert the VRM into the connector by aligning the edges of the VRM with the slots at the end of the VRM connector. Firmly press the VRM straight down into the connector. Note: Make sure that the "Front" label on the VRM is facing the front of the server. 16. Replace the microprocessor air baffle between socket 1 and socket 2, if you removed it. 17. Rotate the media hood to the closed position and tighten the captive screws. If you have other devices to install or remove, do so now. Otherwise, go to "Completing the installation." Completing the installation To complete the installation, complete the following steps. Wire cable clip (open) Cable channel 1. Make sure that all internal cables are correctly routed. In the order listed, route the following cables through the cable channel; then, connect the cables to the I/O board. a. SAS power cable b. SAS 4x signal cable c. Operator information panel cable 50 IBM System x3850 M2 and System x3950 M2 Type 7141: User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Alignment indicator
VRM cradle
15.
Install
a
VRM
in
the
connector
next
to
the
microprocessor
socket:
a.
Turn
the
VRM
so
that
the
keys
align
with
the
slot.
b.
Insert
the
VRM
into
the
connector
by
aligning
the
edges
of
the
VRM
with
the
slots
at
the
end
of
the
VRM
connector.
Firmly
press
the
VRM
straight
down
into
the
connector.
Note:
Make
sure
that
the
“Front”
label
on
the
VRM
is
facing
the
front
of
the
server.
16.
Replace
the
microprocessor
air
baffle
between
socket
1
and
socket
2,
if
you
removed
it.
17.
Rotate
the
media
hood
to
the
closed
position
and
tighten
the
captive
screws.
If
you
have
other
devices
to
install
or
remove,
do
so
now.
Otherwise,
go
to
“Completing
the
installation.”
Completing
the
installation
To
complete
the
installation,
complete
the
following
steps.
Wire cable clip (open)
Cable channel
1.
Make
sure
that
all
internal
cables
are
correctly
routed.
In
the
order
listed,
route
the
following
cables
through
the
cable
channel;
then,
connect
the
cables
to
the
I/O
board.
a.
SAS
power
cable
b.
SAS
4x
signal
cable
c.
Operator
information
panel
cable
50
IBM
System
x3850
M2
and
System
x3950
M2
Type
7141:
User’s
Guide