IBM 866631Y Hardware Maintenance Manual - Page 140

Error symptoms, Run Configuration/Setup, enable primary IDE

Get IBM 866631Y - Netfinity 7100 - 8666 PDF manuals and user guides
UPC - 087944569336
View all IBM 866631Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 140 highlights

Error symptoms Error Symptom FRU/Action CD is not working properly. 1. Clean the CD. 2. Run CD-ROM diagnostics. 3. CD-ROM Drive CD-ROM drive tray is not working. (The server must be powered-on.) 1. Insert the end of a paper clip into the manual tray-release opening. 2. Run CD-ROM diagnostics. 3. CD-ROM Drive CD-ROM drive is not recognized. 1. Run Configuration/Setup, enable primary IDE channel. 2. Check cables and jumpers. 3. Check for correct device driver. 4. Run CD-ROM diagnostics. 5. CD-ROM drive 6. I/O Legacy Board Power switch does not work 1. Verify that the power-on control jumper on J23 is on and reset button does work. pins 1 and 2. 2. Power Switch Assembly 3. I/O Legacy Board Diskette drive in-use light stays on, or the system bypasses the diskette drive, or the diskette drive does not work. 1. If there is a diskette in the drive, verify that: a. The diskette drive is enabled in the Configuration/Setup utility program. b. The diskette is good and not damaged. (Try another diskette if you have one.) c. The diskette is inserted correctly in the drive. d. The diskette contains the necessary files to start the server. e. The software program is OK. f. Cable is installed correctly (proper orientation) 2. Run Diskette Drive Diagnostics. 3. Cable 4. Diskette Drive 5. I/O Legacy Board Monitor problems 1. Monitor (general).Some IBM monitors have their own self-tests. If you suspect a problem with 2. Run Video Diagnostics. If diagnostics pass, the problem may be a video driver. the monitor, refer to the 3. Display Adapter / I/O Legacy Board information that comes with the monitor for adjusting and testing instructions. 130 Hardware Maintenance Manual: Netfinity 7100 - Type 8666

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Error symptoms
Error Symptom
FRU/Action
CD is not working properly.
1.
Clean the CD.
2.
Run CD-ROM diagnostics.
3.
CD-ROM Drive
CD-ROM drive tray is not
working.
(The server must
be powered-on.)
1.
Insert the end of a paper clip into the manual
tray-release opening.
2.
Run CD-ROM diagnostics.
3.
CD-ROM Drive
CD-ROM drive is not
recognized.
1.
Run Configuration/Setup, enable primary IDE
channel.
2.
Check cables and jumpers.
3.
Check for correct device driver.
4.
Run CD-ROM diagnostics.
5.
CD-ROM drive
6.
I/O Legacy Board
Power switch does not work
and reset button does work.
1.
Verify that the power-on control jumper on J23 is on
pins 1 and 2.
2.
Power Switch Assembly
3.
I/O Legacy Board
Diskette drive in-use light
stays on, or the system
bypasses the diskette drive,
or the diskette drive does
not work.
1.
If there is a diskette in the drive, verify that:
a.
The diskette drive is enabled in the
Configuration/Setup utility program.
b.
The diskette is good and not damaged. (Try another
diskette if you have one.)
c.
The diskette is inserted correctly in the drive.
d.
The diskette contains the necessary files to start the
server.
e.
The software program is OK.
f.
Cable is installed correctly (proper orientation)
2.
Run Diskette Drive Diagnostics.
3.
Cable
4.
Diskette Drive
5.
I/O Legacy Board
Monitor problems
(general).
Some IBM monitors
have their own self-tests. If
you suspect a problem with
the monitor, refer to the
information that comes with
the monitor for adjusting and
testing instructions.
1.
Monitor
2.
Run Video Diagnostics. If diagnostics pass, the problem
may be a video driver.
3.
Display Adapter / I/O Legacy Board
130
Hardware Maintenance Manual: Netfinity 7100 – Type 8666