IBM 866631Y Hardware Maintenance Manual - Page 72

Completing the installation, When you have the fan assembly properly seated, push on the pop rivet

Get IBM 866631Y - Netfinity 7100 - 8666 PDF manuals and user guides
UPC - 087944569336
View all IBM 866631Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Refer to the following illustration to replace a hot-swap fan. Hot-swap fan assembly 1 Hot-swap fan assembly 3 Latch Hot-swap fan assembly 2 Hot-swap fan assembly 4 To replace a hot-swap fan assembly: 1. Review the information in "Before you begin" on page 43. 2. If you are replacing fan assembly 1, 2, or 3: a. Remove the top cover. Attention: To ensure proper system cooling, keep the cover removed for no more than 30 minutes during this procedure. b. Press the fan release latch and lift the fan assembly out of the server. c. Slide the replacement fan assembly into the server. The latch will snap into place and secure the fan in the server. d. Replace the top cover 3. If you are replacing fan assembly 4: a. Pull out on the orange pop rivet on the rear fan bracket; then, lift the fan assembly up and out of the hinge cutouts. b. Slide the replacement fan assembly into the server. (Make sure that the fan assembly fits correctly into the hinge cutouts on the rear of the shuttle.) c. When you have the fan assembly properly seated, push on the pop rivet until it clicks into place. Completing the installation To complete the installation, you must reinstall the media bay bezel, reinstall the front door, reinstall the top cover, and reconnect all the cables that you disconnected, and for certain options, run the Configuration/Setup Utility program. Follow the instructions in this section. 62 Hardware Maintenance Manual: Netfinity 7100 - Type 8666

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
Refer to the following illustration to replace a hot-swap fan.
Hot-swap fan
assembly 3
Hot-swap fan
assembly 4
Hot-swap fan
assembly 1
Hot-swap fan
assembly 2
Latch
To replace a hot-swap fan assembly:
1.
Review the information in “Before you begin” on page 43.
2.
If you are replacing fan assembly 1, 2, or 3:
a.
Remove the top cover.
Attention:
To ensure proper system cooling, keep the cover removed for
no more than 30 minutes during this procedure.
b.
Press the fan release latch and lift the fan assembly out of the server.
c.
Slide the replacement fan assembly into the server. The latch will snap into
place and secure the fan in the server.
d.
Replace the top cover
3.
If you are replacing fan assembly 4:
a.
Pull out on the orange pop rivet on the rear fan bracket; then, lift the fan
assembly up and out of the hinge cutouts.
b.
Slide the replacement fan assembly into the server. (Make sure that the fan
assembly fits correctly into the hinge cutouts on the rear of the shuttle.)
c.
When you have the fan assembly properly seated, push on the pop rivet
until it clicks into place.
Completing the installation
To complete the installation, you must reinstall the media bay bezel, reinstall the
front door, reinstall the top cover, and reconnect all the cables that you
disconnected, and for certain options, run the Configuration/Setup Utility
program. Follow the instructions in this section.
62
Hardware Maintenance Manual: Netfinity 7100 – Type 8666