IBM 866631Y Hardware Maintenance Manual - Page 62

A drive placement guide is located on the inside edge of the bezel.

Get IBM 866631Y - Netfinity 7100 - 8666 PDF manuals and user guides
UPC - 087944569336
View all IBM 866631Y manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

v Read "Safety information" on page 152. v Review the information in "Before you begin" on page 43. v Read the documentation that comes with the option. Slim filler Filler panel Drive tray handle (in open position) Note: You do not have to turn off the server to install hot-swap drives in these bays. To install a drive in a hot-swap bay: 1. Review the information in "Before you begin" on page 43. 2. Unlock and open the server front door, if you are installing a drive in a tower model. 3. Remove the filler panel from one of the empty hot-swap bays by inserting your finger into the depression at the left side of the filler panel and pulling it away from the server. Attention: To maintain proper system cooling, do not operate the server for more than 10 minutes without either a drive or a filler panel installed for each bay. 4. Install the hard disk drive in the hot-swap bay: a. If there is a small gap above or below the drive, separate the slim filler from the filler panel, and insert it into the gap. Note: A drive placement guide is located on the inside edge of the bezel. The drive placement guide indicates the placement for slim-high and half-high drives. The guide also shows the SCSI ID assigned to the drive. b. Ensure that the tray handle is open (that is, perpendicular to the drive). c. Align the drive assembly with the guide rails in the bay. d. Gently push the drive assembly into the bay until the drive stops. e. Push the tray handle to the closed (locked) position. f. Check the hard disk drive status indicator to verify that the hard disk drive is operating properly. 52 Hardware Maintenance Manual: Netfinity 7100 - Type 8666

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
v
Read “Safety information” on page 152.
v
Review the information in “Before you begin” on page 43.
v
Read the documentation that comes with the option.
Slim filler
Filler panel
Drive tray handle
(in open position)
Note:
You do not have to turn off the server to install hot-swap drives in these
bays.
To install a drive in a hot-swap bay:
1.
Review the information in “Before you begin” on page 43.
2.
Unlock and open the server front door, if you are installing a drive in a tower
model.
3.
Remove the filler panel from one of the empty hot-swap bays by inserting your
finger into the depression at the left side of the filler panel and pulling it away
from the server.
Attention:
To maintain proper system cooling, do not operate the server for
more than 10 minutes without either a drive or a filler panel
installed for each bay.
4.
Install the hard disk drive in the hot-swap bay:
a.
If there is a small gap above or below the drive, separate the slim filler from
the filler panel, and insert it into the gap.
Note:
A drive placement guide is located on the inside edge of the bezel.
The drive placement guide indicates the placement for slim-high and
half-high drives. The guide also shows the SCSI ID assigned to the
drive.
b.
Ensure that the tray handle is open (that is, perpendicular to the drive).
c.
Align the drive assembly with the guide rails in the bay.
d.
Gently push the drive assembly into the bay until the drive stops.
e.
Push the tray handle to the closed (locked) position.
f.
Check the hard disk drive status indicator to verify that the hard disk drive
is operating properly.
52
Hardware Maintenance Manual: Netfinity 7100 – Type 8666