Home » Intel Manuals » Processors » Intel Q9300 » Manual Viewer

Intel Q9300 Data Sheet - Page 35

Package Mechanical, Specifications

UPC - 675900938236

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Package Mechanical Specifications 3 Package Mechanical Specifications The processor is packaged in a Flip-Chip Land Grid Array (FC-LGA6) package that interfaces with the motherboard via an LGA775 socket. The package consists of a processor core mounted on a substrate land-carrier. An integrated heat spreader (IHS) is attached to the package substrate and core and serves as the mating surface for processor component thermal solutions, such as a heatsink. Figure 3-1 shows a sketch of the processor package components and how they are assembled together. Refer to the LGA775 Socket Mechanical Design Guide for complete details on the LGA775 socket. The package components shown in Figure 3-1 include the following: • Integrated Heat Spreader (IHS) • Thermal Interface Material (TIM) • Processor core (die) • Package substrate • Capacitors Figure 3-1. Processor Package Assembly Sketch Core (die) TIM IHS Substrate System Board Capacitors LGA775 Socket 3.1 NOTE: 1. Socket and motherboard are included for reference and are not part of processor package. Package Mechanical Drawing The package mechanical drawings are shown in Figure 3-2 and Figure 3-3. The drawings include dimensions necessary to design a thermal solution for the processor. These dimensions include: • Package reference with tolerances (total height, length, width, etc.) • IHS parallelism and tilt • Land dimensions • Top-side and back-side component keep-out dimensions • Reference datums • All drawing dimensions are in mm [in]. • Guidelines on potential IHS flatness variation with socket load plate actuation and installation of the cooling solution is available in the processor Thermal and Mechanical Design Guidelines. Datasheet 35

Section	Page
Intel® Core™2 Extreme Processor QX9000D Series, Intel® Core™2 Quad Processor Q9000D, Q9000SD, Q8000D, and Q8000SD Series	1
Contents	3
Figures	5
Tables	6
Revision History	7
Intel® Core™2 Extreme Processor QX9000 Series and Intel® Core™2 Quad Processor Q9000, Q9000S, Q8000, Q8000S Series Features	9
1 Introduction	11
1.1 Terminology	12
1.1.1 Processor Terminology Definitions	12
1.2 References	14
2 Electrical Specifications	15
2.1 Power and Ground Lands	15
2.2 Decoupling Guidelines	15
2.2.1 VCC Decoupling	15
2.2.2 Vtt Decoupling	15
2.2.3 FSB Decoupling	16
2.3 Voltage Identification	16
2.4 Reserved, Unused, and TESTHI Signals	18
2.5 Power Segment Identifier (PSID)	18
2.6 Voltage and Current Specification	19
2.6.1 Absolute Maximum and Minimum Ratings	19
2.6.2 DC Voltage and Current Specification	20
2.6.3 VCC Overshoot	25
2.6.4 Die Voltage Validation	25
2.7 Signaling Specifications	26
2.7.1 FSB Signal Groups	26
2.7.2 CMOS and Open Drain Signals	28
2.7.3 Processor DC Specifications	28
2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications	29
2.7.3.2 GTL+ Front Side Bus Specifications	30
2.8 Clock Specifications	31
2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	31
2.8.2 FSB Frequency Select Signals (BSEL[2:0])	32
2.8.3 Phase Lock Loop (PLL) and Filter	32
2.8.4 BCLK[1:0] Specifications	32
3 Package Mechanical Specifications	35
3.1 Package Mechanical Drawing	35
3.2 Processor Component Keep-Out Zones	39
3.3 Package Loading Specifications	39
3.4 Package Handling Guidelines	39
3.5 Package Insertion Specifications	40
3.6 Processor Mass Specification	40
3.7 Processor Materials	40
3.8 Processor Markings	40
4 Land Listing and Signal Descriptions	43
4.1 Processor Land Assignments	43
4.2 Alphabetical Signals Reference	64
5 Thermal Specifications and Design Considerations	75
5.1 Processor Thermal Specifications	75
5.1.1 Thermal Specifications	75
5.1.2 Thermal Metrology	81
5.2 Processor Thermal Features	81
5.2.1 Thermal Monitor	81
5.2.2 Thermal Monitor 2	82
5.2.3 On-Demand Mode	83
5.2.4 PROCHOT# Signal	84
5.2.5 THERMTRIP# Signal	84
5.3 Platform Environment Control Interface (PECI)	85
5.3.1 Introduction	85
5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems	85
5.3.2 PECI Specifications	86
5.3.2.1 PECI Device Address	86
5.3.2.2 PECI Command Support	86
5.3.2.3 PECI Fault Handling Requirements	86
5.3.2.4 PECI GetTemp0() Error Code Support	86
6 Features	87
6.1 Power-On Configuration Options	87
6.2 Clock Control and Low Power States	87
6.2.1 Normal State	88
6.2.2 HALT and Extended HALT Powerdown States	88
6.2.2.1 HALT Powerdown State	88
6.2.2.2 Extended HALT Powerdown State	89
6.2.3 Stop Grant and Extended Stop Grant States	89
6.2.3.1 Stop-Grant State	89
6.2.3.2 Extended Stop Grant State	90
6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State	90
6.2.4.1 HALT Snoop State, Stop Grant Snoop State	90
6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State	90
6.2.5 Sleep State	90
6.2.6 Deep Sleep State	91
6.2.7 Deeper Sleep State	91
6.2.8 Enhanced Intel SpeedStep® Technology	92
6.3 Processor Power Status Indicator (PSI) Signal	92
7 Boxed Processor Specifications	93
7.1 Introduction	93
7.2 Mechanical Specifications	94
7.2.1 Boxed Processor Cooling Solution Dimensions	94
7.2.2 Boxed Processor Fan Heatsink Weight	95
7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly	95
7.3 Electrical Requirements	95
7.3.1 Fan Heatsink Power Supply	95
7.4 Thermal Specifications	97
7.4.1 Boxed Processor Cooling Requirements	97
7.4.2 Variable Speed Fan	98
7.5 Boxed Intel® Core™2 Extreme Processor QX9650 Specifications	99
7.5.1 Boxed Intel® Core™2 Extreme Processor QX9650 Fan Heatsink Weight	100
8 Debug Tools Specifications	103
8.1 Logic Analyzer Interface (LAI)	103
8.1.1 Mechanical Considerations	103