Home » Intel Manuals » Processors » Intel Q9300 » Manual Viewer

Intel Q9300 Data Sheet - Page 66

Table 4-3., Signal Description, Sheet 3 of 10 - driver

UPC - 675900938236

Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Land Listing and Signal Descriptions Table 4-3. Signal Description (Sheet 3 of 10) Name Type Description D[63:0]# (Data) are the data signals. These signals provide a 64bit data path between the processor FSB agents, and must connect the appropriate pins/lands on all such agents. The data driver asserts DRDY# to indicate a valid data transfer. D[63:0]# are quad-pumped signals and will, thus, be driven four times in a common clock period. D[63:0]# are latched off the falling edge of both DSTBP[3:0]# and DSTBN[3:0]#. Each group of 16 data signals correspond to a pair of one DSTBP# and one DSTBN#. The following table shows the grouping of data signals to data strobes and DBI#. D[63:0]# Input/ Output Quad-Pumped Signal Groups Data Group DSTBN#/ DSTBP# DBI# D[15:0]# 0 0 D[31:16]# 1 1 D[47:32]# 2 2 D[63:48]# 3 3 DBI[3:0]# DBR# DBSY# Furthermore, the DBI# signals determine the polarity of the data signals. Each group of 16 data signals corresponds to one DBI# signal. When the DBI# signal is active, the corresponding data group is inverted and therefore sampled active high. DBI[3:0]# (Data Bus Inversion) are source synchronous and indicate the polarity of the D[63:0]# signals.The DBI[3:0]# signals are activated when the data on the data bus is inverted. If more than half the data bits, within a 16-bit group, would have been asserted electrically low, the bus agent may invert the data bus signals for that particular sub-phase for that 16-bit group. Input/ Output DBI[3:0] Assignment To Data Bus Bus Signal Data Bus Signals Output Input/ Output DBI3# D[63:48]# DBI2# D[47:32]# DBI1# D[31:16]# DBI0# D[15:0]# DBR# (Debug Reset) is used only in processor systems where no debug port is implemented on the system board. DBR# is used by a debug port interposer so that an in-target probe can drive system reset. If a debug port is implemented in the system, DBR# is a no connect in the system. DBR# is not a processor signal. DBSY# (Data Bus Busy) is asserted by the agent responsible for driving data on the processor FSB to indicate that the data bus is in use. The data bus is released after DBSY# is de-asserted. This signal must connect the appropriate pins/lands on all processor FSB agents. 66 Datasheet

Section	Page
Intel® Core™2 Extreme Processor QX9000D Series, Intel® Core™2 Quad Processor Q9000D, Q9000SD, Q8000D, and Q8000SD Series	1
Contents	3
Figures	5
Tables	6
Revision History	7
Intel® Core™2 Extreme Processor QX9000 Series and Intel® Core™2 Quad Processor Q9000, Q9000S, Q8000, Q8000S Series Features	9
1 Introduction	11
1.1 Terminology	12
1.1.1 Processor Terminology Definitions	12
1.2 References	14
2 Electrical Specifications	15
2.1 Power and Ground Lands	15
2.2 Decoupling Guidelines	15
2.2.1 VCC Decoupling	15
2.2.2 Vtt Decoupling	15
2.2.3 FSB Decoupling	16
2.3 Voltage Identification	16
2.4 Reserved, Unused, and TESTHI Signals	18
2.5 Power Segment Identifier (PSID)	18
2.6 Voltage and Current Specification	19
2.6.1 Absolute Maximum and Minimum Ratings	19
2.6.2 DC Voltage and Current Specification	20
2.6.3 VCC Overshoot	25
2.6.4 Die Voltage Validation	25
2.7 Signaling Specifications	26
2.7.1 FSB Signal Groups	26
2.7.2 CMOS and Open Drain Signals	28
2.7.3 Processor DC Specifications	28
2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications	29
2.7.3.2 GTL+ Front Side Bus Specifications	30
2.8 Clock Specifications	31
2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	31
2.8.2 FSB Frequency Select Signals (BSEL[2:0])	32
2.8.3 Phase Lock Loop (PLL) and Filter	32
2.8.4 BCLK[1:0] Specifications	32
3 Package Mechanical Specifications	35
3.1 Package Mechanical Drawing	35
3.2 Processor Component Keep-Out Zones	39
3.3 Package Loading Specifications	39
3.4 Package Handling Guidelines	39
3.5 Package Insertion Specifications	40
3.6 Processor Mass Specification	40
3.7 Processor Materials	40
3.8 Processor Markings	40
4 Land Listing and Signal Descriptions	43
4.1 Processor Land Assignments	43
4.2 Alphabetical Signals Reference	64
5 Thermal Specifications and Design Considerations	75
5.1 Processor Thermal Specifications	75
5.1.1 Thermal Specifications	75
5.1.2 Thermal Metrology	81
5.2 Processor Thermal Features	81
5.2.1 Thermal Monitor	81
5.2.2 Thermal Monitor 2	82
5.2.3 On-Demand Mode	83
5.2.4 PROCHOT# Signal	84
5.2.5 THERMTRIP# Signal	84
5.3 Platform Environment Control Interface (PECI)	85
5.3.1 Introduction	85
5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems	85
5.3.2 PECI Specifications	86
5.3.2.1 PECI Device Address	86
5.3.2.2 PECI Command Support	86
5.3.2.3 PECI Fault Handling Requirements	86
5.3.2.4 PECI GetTemp0() Error Code Support	86
6 Features	87
6.1 Power-On Configuration Options	87
6.2 Clock Control and Low Power States	87
6.2.1 Normal State	88
6.2.2 HALT and Extended HALT Powerdown States	88
6.2.2.1 HALT Powerdown State	88
6.2.2.2 Extended HALT Powerdown State	89
6.2.3 Stop Grant and Extended Stop Grant States	89
6.2.3.1 Stop-Grant State	89
6.2.3.2 Extended Stop Grant State	90
6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State	90
6.2.4.1 HALT Snoop State, Stop Grant Snoop State	90
6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State	90
6.2.5 Sleep State	90
6.2.6 Deep Sleep State	91
6.2.7 Deeper Sleep State	91
6.2.8 Enhanced Intel SpeedStep® Technology	92
6.3 Processor Power Status Indicator (PSI) Signal	92
7 Boxed Processor Specifications	93
7.1 Introduction	93
7.2 Mechanical Specifications	94
7.2.1 Boxed Processor Cooling Solution Dimensions	94
7.2.2 Boxed Processor Fan Heatsink Weight	95
7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly	95
7.3 Electrical Requirements	95
7.3.1 Fan Heatsink Power Supply	95
7.4 Thermal Specifications	97
7.4.1 Boxed Processor Cooling Requirements	97
7.4.2 Variable Speed Fan	98
7.5 Boxed Intel® Core™2 Extreme Processor QX9650 Specifications	99
7.5.1 Boxed Intel® Core™2 Extreme Processor QX9650 Fan Heatsink Weight	100
8 Debug Tools Specifications	103
8.1 Logic Analyzer Interface (LAI)	103
8.1.1 Mechanical Considerations	103

Match case Limit results 1 per page

Land Listing and Signal Descriptions

Datasheet

D[63:0]#

Input/

Output

D[63:0]# (Data) are the data signals. These signals provide a 64-

bit data path between the processor FSB agents, and must

connect the appropriate pins/lands on all such agents. The data

driver asserts DRDY# to indicate a valid data transfer.

D[63:0]# are quad-pumped signals and will, thus, be driven four

times in a common clock period. D[63:0]# are latched off the

falling edge of both DSTBP[3:0]# and DSTBN[3:0]#. Each group

of 16 data signals correspond to a pair of one DSTBP# and one

DSTBN#. The following table shows the grouping of data signals

to data strobes and DBI#.

Furthermore, the DBI# signals determine the polarity of the data

signals. Each group of 16 data signals corresponds to one DBI#

signal. When the DBI# signal is active, the corresponding data

group is inverted and therefore sampled active high.

DBI[3:0]#

Input/

Output

DBI[3:0]# (Data Bus Inversion) are source synchronous and

indicate the polarity of the D[63:0]# signals.The DBI[3:0]#

signals are activated when the data on the data bus is inverted. If

more than half the data bits, within a 16-bit group, would have

been asserted electrically low, the bus agent may invert the data

bus signals for that particular sub-phase for that 16-bit group.

DBR#

Output

DBR# (Debug Reset) is used only in processor systems where no

debug port is implemented on the system board. DBR# is used by

a debug port interposer so that an in-target probe can drive

system reset. If a debug port is implemented in the system, DBR#

is a no connect in the system. DBR# is not a processor signal.

DBSY#

Input/

Output

DBSY# (Data Bus Busy) is asserted by the agent responsible for

driving data on the processor FSB to indicate that the data bus is

in use. The data bus is released after DBSY# is de-asserted. This

signal must connect the appropriate pins/lands on all processor

FSB agents.

Table 4-3.

Signal Description

(Sheet 3 of 10)

Name

Type

Description

Quad-Pumped Signal Groups

Data Group

DSTBN#/

DSTBP#

DBI#

D[15:0]#

D[31:16]#

D[47:32]#

D[63:48]#

DBI[3:0] Assignment To Data Bus

Bus Signal

Data Bus

Signals

DBI3#

D[63:48]#

DBI2#

D[47:32]#

DBI1#

D[31:16]#

DBI0#

D[15:0]#