Intel Q9300 Data Sheet - Page 70

Land Listing and Signal Descriptions

70

Datasheet

PWRGOOD

Input

PWRGOOD (Power Good) is a processor input. The processor

requires this signal to be a clean indication that the clocks and

power supplies are stable and within their specifications. ‘Clean’

implies that the signal will remain low (capable of sinking leakage

current), without glitches, from the time that the power supplies

are turned on until they come within specification. The signal must

then transition monotonically to a high state. PWRGOOD can be

driven inactive at any time, but clocks and power must again be

stable before a subsequent rising edge of PWRGOOD.

The PWRGOOD signal must be supplied to the processor; it is used

to protect internal circuits against voltage sequencing issues. It

should be driven high throughout boundary scan operation.

REQ[4:0]#

Input/

Output

REQ[4:0]# (Request Command) must connect the appropriate

pins/lands of all processor FSB agents. They are asserted by the

current bus owner to define the currently active transaction type.

These signals are source synchronous to ADSTB0#.

RESET#

Input

Asserting the RESET# signal resets the processor to a known

state and invalidates its internal caches without writing back any

of their contents. For a power-on Reset, RESET# must stay active

for at least one millisecond after V

CC

and BCLK have reached their

proper specifications. On observing active RESET#, all FSB agents

will de-assert their outputs within two clocks. RESET# must not be

kept asserted for more than 10 ms while PWRGOOD is asserted.

A number of bus signals are sampled at the active-to-inactive

transition of RESET# for power-on configuration. These

configuration options are described in the

Section 6.1

.

This signal does not have on-die termination and must be

terminated on the system board.

RESERVED

All RESERVED lands must remain unconnected. Connection of

these lands to V

CC

, V

SS

, V

TT

, or to any other signal (including each

other) can result in component malfunction or incompatibility with

future processors.

RS[2:0]#

Input

RS[2:0]# (Response Status) are driven by the response agent

(the agent responsible for completion of the current transaction),

and must connect the appropriate pins/lands of all processor FSB

agents.

SKTOCC#

Output

SKTOCC# (Socket Occupied) will be pulled to ground by the

processor. System board designers may use this signal to

determine if the processor is present.

Table 4-3.

Signal Description

(Sheet 7 of 10)

Name

Type

Description

Section	Page
Intel® Core™2 Extreme Processor QX9000D Series, Intel® Core™2 Quad Processor Q9000D, Q9000SD, Q8000D, and Q8000SD Series	1
Contents	3
Figures	5
Tables	6
Revision History	7
Intel® Core™2 Extreme Processor QX9000 Series and Intel® Core™2 Quad Processor Q9000, Q9000S, Q8000, Q8000S Series Features	9
1 Introduction	11
1.1 Terminology	12
1.1.1 Processor Terminology Definitions	12
1.2 References	14
2 Electrical Specifications	15
2.1 Power and Ground Lands	15
2.2 Decoupling Guidelines	15
2.2.1 VCC Decoupling	15
2.2.2 Vtt Decoupling	15
2.2.3 FSB Decoupling	16
2.3 Voltage Identification	16
2.4 Reserved, Unused, and TESTHI Signals	18
2.5 Power Segment Identifier (PSID)	18
2.6 Voltage and Current Specification	19
2.6.1 Absolute Maximum and Minimum Ratings	19
2.6.2 DC Voltage and Current Specification	20
2.6.3 VCC Overshoot	25
2.6.4 Die Voltage Validation	25
2.7 Signaling Specifications	26
2.7.1 FSB Signal Groups	26
2.7.2 CMOS and Open Drain Signals	28
2.7.3 Processor DC Specifications	28
2.7.3.1 Platform Environment Control Interface (PECI) DC Specifications	29
2.7.3.2 GTL+ Front Side Bus Specifications	30
2.8 Clock Specifications	31
2.8.1 Front Side Bus Clock (BCLK[1:0]) and Processor Clocking	31
2.8.2 FSB Frequency Select Signals (BSEL[2:0])	32
2.8.3 Phase Lock Loop (PLL) and Filter	32
2.8.4 BCLK[1:0] Specifications	32
3 Package Mechanical Specifications	35
3.1 Package Mechanical Drawing	35
3.2 Processor Component Keep-Out Zones	39
3.3 Package Loading Specifications	39
3.4 Package Handling Guidelines	39
3.5 Package Insertion Specifications	40
3.6 Processor Mass Specification	40
3.7 Processor Materials	40
3.8 Processor Markings	40
4 Land Listing and Signal Descriptions	43
4.1 Processor Land Assignments	43
4.2 Alphabetical Signals Reference	64
5 Thermal Specifications and Design Considerations	75
5.1 Processor Thermal Specifications	75
5.1.1 Thermal Specifications	75
5.1.2 Thermal Metrology	81
5.2 Processor Thermal Features	81
5.2.1 Thermal Monitor	81
5.2.2 Thermal Monitor 2	82
5.2.3 On-Demand Mode	83
5.2.4 PROCHOT# Signal	84
5.2.5 THERMTRIP# Signal	84
5.3 Platform Environment Control Interface (PECI)	85
5.3.1 Introduction	85
5.3.1.1 TCONTROL and TCC activation on PECI-Based Systems	85
5.3.2 PECI Specifications	86
5.3.2.1 PECI Device Address	86
5.3.2.2 PECI Command Support	86
5.3.2.3 PECI Fault Handling Requirements	86
5.3.2.4 PECI GetTemp0() Error Code Support	86
6 Features	87
6.1 Power-On Configuration Options	87
6.2 Clock Control and Low Power States	87
6.2.1 Normal State	88
6.2.2 HALT and Extended HALT Powerdown States	88
6.2.2.1 HALT Powerdown State	88
6.2.2.2 Extended HALT Powerdown State	89
6.2.3 Stop Grant and Extended Stop Grant States	89
6.2.3.1 Stop-Grant State	89
6.2.3.2 Extended Stop Grant State	90
6.2.4 Extended HALT Snoop State, HALT Snoop State, Extended Stop Grant Snoop State, and Stop Grant Snoop State	90
6.2.4.1 HALT Snoop State, Stop Grant Snoop State	90
6.2.4.2 Extended HALT Snoop State, Extended Stop Grant Snoop State	90
6.2.5 Sleep State	90
6.2.6 Deep Sleep State	91
6.2.7 Deeper Sleep State	91
6.2.8 Enhanced Intel SpeedStep® Technology	92
6.3 Processor Power Status Indicator (PSI) Signal	92
7 Boxed Processor Specifications	93
7.1 Introduction	93
7.2 Mechanical Specifications	94
7.2.1 Boxed Processor Cooling Solution Dimensions	94
7.2.2 Boxed Processor Fan Heatsink Weight	95
7.2.3 Boxed Processor Retention Mechanism and Heatsink Attach Clip Assembly	95
7.3 Electrical Requirements	95
7.3.1 Fan Heatsink Power Supply	95
7.4 Thermal Specifications	97
7.4.1 Boxed Processor Cooling Requirements	97
7.4.2 Variable Speed Fan	98
7.5 Boxed Intel® Core™2 Extreme Processor QX9650 Specifications	99
7.5.1 Boxed Intel® Core™2 Extreme Processor QX9650 Fan Heatsink Weight	100
8 Debug Tools Specifications	103
8.1 Logic Analyzer Interface (LAI)	103
8.1.1 Mechanical Considerations	103

Intel Q9300 Data Sheet - Page 70

Table 4-3., Signal Description, Sheet 7 of 10 - socket type

Page 70 highlights