Intel SE440BX-2 Product Guide - Page 31

How to Remove Memory, Turn off the computer.

Get Intel SE440BX-2 - Desktop Board Motherboard PDF manuals and user guides
UPC - 735858129466
View all Intel SE440BX-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

SE440BX-2 Motherboard Product Guide 6. Position the DIMM above the socket. Align the two small notches in the bottom edge of the DIMM with the keys in the socket. 7. Insert the bottom edge of the DIMM into the socket (see Figure 13). 8. When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips snap into place. Make sure the clips are firmly in place. 9. Replace the computer cover. 10. If you installed a DIMM with ECC memory, turn on the computer and use the ECC Configuration feature in Setup to enable ECC (see Chapter 3). Figure 13. Installing a DIMM OM07172 How to Remove Memory To remove a DIMM, follow these steps: 1. Observe the precautions in "Before You Begin" (see page 19). 2. Turn off all peripheral devices connected to the computer. Turn off the computer. 3. Remove the computer cover. 4. Gently spread the retaining clips at each end of the socket. The DIMM pops out of the socket. 5. Hold the DIMM by the edges, lift it away from the socket, and store it in an antistatic package. 6. Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets. 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
SE440BX-2 Motherboard Product Guide
31
6.
Position the DIMM above the socket.
Align the two small notches in the bottom edge of the
DIMM with the keys in the socket.
7.
Insert the bottom edge of the DIMM into the socket (see Figure 13).
8.
When the DIMM is seated, push down on the top edge of the DIMM until the retaining clips
snap into place.
Make sure the clips are firmly in place.
9.
Replace the computer cover.
10. If you installed a DIMM with ECC memory, turn on the computer and use the ECC
Configuration feature in Setup to enable ECC (see Chapter 3).
OM07172
Figure 13.
Installing a DIMM
How to Remove Memory
To remove a DIMM, follow these steps:
1.
Observe the precautions in "Before You Begin" (see page 19).
2.
Turn off all peripheral devices connected to the computer.
Turn off the computer.
3.
Remove the computer cover.
4.
Gently spread the retaining clips at each end of the socket.
The DIMM pops out of the socket.
5.
Hold the DIMM by the edges, lift it away from the socket, and store it in an antistatic package.
6.
Reinstall and reconnect any parts you removed or disconnected to reach the DIMM sockets.