Intel SR1520MLNA User Guide - Page 35

Installing and Removing a Hard Drive

Get Intel SR1520MLNA - Sy 1U 600W Dual X38Ml Mb 2.5Sata Hdd Ddr2 2Pci-E X16 Risers PDF manuals and user guides
UPC - 735858197434
View all Intel SR1520MLNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Installing the Server System Cover 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information" on page iii. 2. Place the cover over the server system so that the side edges of the cover sit just outside of the server system sidewalls. Slide the cover forward. See letter "A" in the figure below. 3. Insert the larger screw at the rear of the system. See letter "B" in the figure. 4. Insert the two small screws on the top surface of the cover, near the front edge. See letter "C". B A C AF002501 Figure 9. Installing the Server System Cover 5. Reconnect all peripheral devices and the AC power cord. Installing and Removing a Hard Drive Caution: The hard drives are NOT hot swappable. Before removing or replacing a hard drive, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet. One SATA drive can be installed for each server board (two drives total). Both drive bays are at the right side of the chassis. Intel® Server System SR1520ML User's Guide 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Intel
®
Server System SR1520ML User’s Guide
15
Installing the Server System Cover
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information” on page iii
.
2.
Place the cover over the server system so that the side edges of the cover sit just
outside of the server system sidewalls. Slide the cover forward. See letter “A” in the
figure below.
3.
Insert the larger screw at the rear of the system. See letter “B” in the figure.
4.
Insert the two small screws on the top surface of the cover, near the front edge. See
letter “C”.
Figure 9. Installing the Server System Cover
5.
Reconnect all peripheral devices and the AC power cord.
Installing and Removing a Hard Drive
Caution:
The hard drives are NOT hot swappable. Before removing or replacing a hard drive, you
must first take the server out of service, turn off all peripheral devices connected to the
system, turn off the system by pressing the power button, and unplug the AC power cord
from the system or wall outlet.
One SATA drive can be installed for each server board (two drives total). Both drive bays
are at the right side of the chassis.
AF002501
A
C
B