Intel SR1520MLNA User Guide - Page 46

Installing and Removing a PCI Add-in Card

Get Intel SR1520MLNA - Sy 1U 600W Dual X38Ml Mb 2.5Sata Hdd Ddr2 2Pci-E X16 Risers PDF manuals and user guides
UPC - 735858197434
View all Intel SR1520MLNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing and Removing a PCI Add-in Card Caution: The add-in cards are NOT hot swappable. Before removing or replacing an add-in card, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet. Installing a PCI Add-in Card 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information" on page iii. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the server system cover. For instructions, see "Removing the Server System Cover" on page 14. 4. Remove the PCI riser assembly. For instructions, see "Removing the PCI Riser Assembly" on page 21. 5. Remove the screw from the add-in card slot opening. 6. If a filler panel is installed over the opening at the rear of the riser assembly, remove it. Save the filler panel in case you need it to remove the add-in card later. 7. Insert the add-in card into the socket in the riser assembly. Push the add-in card into place firmly until it seats in the riser card connector, but use caution so you do not twist or bend the card. See letter "A" in the figure below. 8. Re-install the screw you removed in step 5. See letter "B" in the figure. B A Figure 19. Installing an Add-In Card AF002515 26 Intel® Server System SR1520ML User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
26
Intel
®
Server System SR1520ML User’s Guide
Installing and Removing a PCI Add-in Card
Caution:
The add-in cards are NOT hot swappable. Before removing or replacing an add-in card,
you must first take the server out of service, turn off all peripheral devices connected to
the system, turn off the system by pressing the power button, and unplug the AC power
cord from the system or wall outlet.
Installing a PCI Add-in Card
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information” on page iii
.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the server system cover. For instructions, see
“Removing the Server
System Cover” on page 14
.
4.
Remove the PCI riser assembly. For instructions, see
“Removing the PCI Riser
Assembly” on page 21
.
5.
Remove the screw from the add-in card slot opening.
6.
If a filler panel is installed over the opening at the rear of the riser assembly,
remove it. Save the filler panel in case you need it to remove the add-in card later.
7.
Insert the add-in card into the socket in the riser assembly. Push the add-in card into
place firmly until it seats in the riser card connector, but use caution so you do not
twist or bend the card. See letter “A” in the figure below.
8.
Re-install the screw you removed in step 5. See letter “B” in the figure.
Figure 19. Installing an Add-In Card
A
B
AF002515