Intel SR1520MLNA User Guide - Page 41

Installing and Removing the PCI Riser Assembly

Get Intel SR1520MLNA - Sy 1U 600W Dual X38Ml Mb 2.5Sata Hdd Ddr2 2Pci-E X16 Risers PDF manuals and user guides
UPC - 735858197434
View all Intel SR1520MLNA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the server system cover. For instructions, see "Removing the Server System Cover" on page 14. 4. Follow the instructions in the document titled Intel® Z-U130 Value Solid State Drive Mounting Kit Installation Guide for Intel® Server Systems. Note: Your server system includes a USB Y-cable attached to the server board. One part of this cable is attached to the front panel board. The other cable is loose. This loose cable is for the Intel® VSSD. 5. Install the server system cover. For instructions, see "Installing the Server System Cover". 6. Plug all peripheral devices and the AC power cable into the server. Installing and Removing the PCI Riser Assembly Caution: The PCI riser assembly is NOT hot swappable. Before removing or replacing the PCI riser assembly, you must first take the server out of service, turn off all peripheral devices connected to the system, turn off the system by pressing the power button, and unplug the AC power cord from the system or wall outlet. Removing the PCI Riser Assembly To remove the PCI riser assembly, use the following instructions. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information" on page iii. 2. Power down the server and unplug all peripheral devices and the AC power cable. 3. Remove the server system cover. For instructions, see "Removing the Server System Cover" on page 14. 4. Disconnect any cables attached to any add-in cards. 5. Remove the screw from the riser assembly bracket. See letter "A" in the following figure. 6. Lift up on the riser assembly to remove it. Use caution to gently ease the riser card from the add-in card slot so you do not damage the slot or the riser card. See letter "B" in the figure. Intel® Server System SR1520ML User's Guide 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
Intel
®
Server System SR1520ML User’s Guide
21
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the server system cover. For instructions, see
“Removing the Server
System Cover” on page 14
.
4.
Follow the instructions in the document titled
Intel
®
Z-U130 Value Solid State
Drive Mounting Kit Installation Guide for Intel
®
Server Systems
.
Note:
Your server system includes a USB Y-cable attached to the server board. One part of this
cable is attached to the front panel board. The other cable is loose. This loose cable is for
the Intel
®
VSSD.
5.
Install the server system cover. For instructions, see
“Installing the Server System
Cover”
.
6.
Plug all peripheral devices and the AC power cable into the server.
Installing and Removing the PCI Riser Assembly
Caution:
The PCI riser assembly is NOT hot swappable. Before removing or replacing the PCI
riser assembly, you must first take the server out of service, turn off all peripheral devices
connected to the system, turn off the system by pressing the power button, and unplug the
AC power cord from the system or wall outlet.
Removing the PCI Riser Assembly
To remove the PCI riser assembly, use the following instructions.
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information” on page iii
.
2.
Power down the server and unplug all peripheral devices and the AC power cable.
3.
Remove the server system cover. For instructions, see
“Removing the Server
System Cover” on page 14
.
4.
Disconnect any cables attached to any add-in cards.
5.
Remove the screw from the riser assembly bracket. See letter “A” in the following
figure.
6.
Lift up on the riser assembly to remove it. Use caution to gently ease the riser card
from the add-in card slot so you do not damage the slot or the riser card. See letter
“B” in the figure.