Invacare IN66AHANFR Owners Manual - Page 20

Front Riggings

Get Invacare IN66AHANFR PDF manuals and user guides View all Invacare IN66AHANFR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

SECTION 4-FRONT RIGGINGS SECTION 4-FRONT RIGGINGS ƽ WARNING After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Otherwise injury or damage may occur. Installing/Removing Front Riggings Assembly NOTE: For this procedure, refer to FIGURE 4.1. Installing 1. Turn the front rigging assembly to the side (open front rigging is perpendicular to wheelchair). 2. Install the hinge plates on the front rigging assembly onto the hinge pins on the wheelchair frame. 3. Push the front rigging assembly towards the inside of the wheelchair until it locks into place. An "audible" click will be heard when locked in place. NOTE: The footplate will be on the inside of the wheelchair when locked in place. Removing 1. Push the front rigging release lever inward. 2. Rotate swingaway front rigging assembly outward. 3. Lift the swingaway front rigging assembly off the hinge pins. DETAIL "A" Front Rigging Assembly DETAIL "B" Front Rigging Release Lever Hinge Plates/ Hinge Pins Hinge Plates/ Hinge Pins Rotate inward to use. Rotate outward to remove FIGURE 4.1 Installing/Removing Front Riggings Assembly Insignia™ 20 Part No. 1163197

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
SECTION 4—FRONT RIGGINGS
Insignia
™
20
Part No. 1163197
SECTION 4—FRONT RIGGINGS
±
WARNING
After any adjustments, repair or service and before use, make sure all attaching hardware is
tightened securely. Otherwise injury or damage may occur.
Installing/Removing Front Riggings Assembly
NOTE: For this procedure, refer to FIGURE 4.1.
Installing
1.
Turn the front rigging assembly to the side (open front rigging is perpendicular to wheelchair).
2.
Install the hinge plates on the front rigging assembly onto the hinge pins on the wheelchair frame.
3.
Push the front rigging assembly towards the inside of the wheelchair until it locks into place. An “audible” click will be
heard when locked in place.
NOTE: The footplate will be on the inside of the wheelchair when locked in place.
Removing
1.
Push the front rigging release lever inward.
2.
Rotate swingaway front rigging assembly outward.
3.
Lift the swingaway front rigging assembly off the hinge pins.
FIGURE 4.1
Installing/Removing Front Riggings Assembly
Front Rigging
Assembly
Hinge Plates/
Hinge Pins
DETAIL “A”
DETAIL “B”
Rotate inward to use.
Rotate outward to remove
Front
Rigging
Release
Lever
Hinge Plates/
Hinge Pins