Kenmore 75121 Owners Manual - Page 8

Removal, Window - window air conditioner

Get Kenmore 75121 - 12,000 BTU Multi-Room Air Conditioner PDF manuals and user guides View all Kenmore 75121 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

J}TJ FRONT INSTALLATION Install the front grille(packed separately) onto the cabinet as follows: • Hook upper tabs of front grille into slots on the cabinet top. (FIG. 19) • Push front grille's tips towards the cabinet in order to snap side tabs into the cabinet. (FIG. 19) • Open the inlet grille. (FIG. 20) • Install the screw (ITEM E) through the front grille. (FIG. 20) • Close inlet grille. (FIG. 21) Top of wood strip should be approximately 3/4" higher than the storm window frame to help condensation to drain properly to the outside. • Install a second wood strip (approximately 6" long by 11/2"wide and same thickness as first strip) in the center of the outer sill flush against the back of the inner sill. Screw the L brackets into this strip. This will raise the L bracket as shown in FIG. 22. WOOD STRIP MOUNTED ON TOP OF INNER SILL 1 1/2" min. (38mm) _"_1 I_" 3/4" j_ "'"-_ _I CLEARANCE T J INNER SILL I / _v _ ILBRACKET/' I WOOD/STRIP STORM _ WINDOW L FRAME I FOR L BRACKET I I_ I I OUTER % INSIDEI I SILL I OUTSIDE FIG. 22 Front Installation FIG. 19 ITEM E -% Front Installation FIG. 20 Front Installation FIG. 21 _IF STOARIRMCOWNINDDITOIOWNEFRRAIMSEBLOCKED BY • If storm window presents interference, fasten a 2" wide wood strip to the inner window sill across the full width of the sill. The wood strip should be thick enough to raise the height of the window sill so that the unit can be installed without interference from the the storm window frame. See FIG. 22. REMOVAL FROM WINDOW • Turn off and unplug the air conditioner. • Remove the front grille. See HOW TO REMOVE THE FRONT GRILLE. Refer to page 13. • Unscrew the side screws that you installed in Step 15. • Slide the air conditioner out of the cabinet. BE CAREFUL NOT TO DROP IT. Hold onto it firmly the whole way sliding it out. Once removed, set it safety out of the way. • Remove the L bracket from window frame and the sash seal from between the windows. • Unscrew the side curtains from the window frame. Fold them back to the sides of the cabinet. • Remove screws attaching cabinet to inner sill. Be careful not to let cabinet fall once screws are removed. • Remove cabinet from window opening. • Place air conditioner into cabinet. Reinstall side screws and Front Grille. • Place unit and all assembly hardware in air conditioner shipping carton, and store in clean, dry place. _!_ [e.7:TIJ i [e] _I • Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. • When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. • Make sure air conditioner does not fall during removal. -8-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
J}TJ FRONT
INSTALLATION
Install the front grille(packed
separately)
onto the
cabinet as follows:
• Hook upper tabs of front grille into slots on the
cabinet
top. (FIG. 19)
• Push front grille's tips towards
the cabinet
in order
to snap side tabs into the cabinet.
(FIG.
19)
• Open the inlet grille. (FIG. 20)
• Install the screw
(ITEM E) through
the front grille.
(FIG. 20)
• Close inlet grille. (FIG. 21)
Front Installation
FIG. 19
ITEM
E
-%
Front Installation
FIG. 20
_!_
[e.7:TIJ
i [e]
_
I
Front Installation
FIG. 21
_IF
AIR CONDITIONER
IS BLOCKED
BY
STORM
WINDOW
FRAME
•
If
storm window presents
interference,
fasten a 2"
wide wood strip to the inner window sill across the full
width of the sill. The wood strip should be thick
enough to raise the height of the window sill so that
the unit can be installed without interference from the
the storm window frame. See FIG. 22.
Top of wood strip should be approximately 3/4"
higher than the storm window frame to help
condensation
to drain properly to the outside.
• Install a second wood strip (approximately 6" long by
11/2"wide and same thickness as first strip) in the
center of the outer sill flush against the back of the
inner sill. Screw the L brackets into this strip.
This will raise the L bracket as shown in FIG. 22.
1 1/2" min.
WOOD STRIP MOUNTED
(38mm)
ON TOP OF INNER SILL
_"_1
I_"
3/4"
j_
"'"-_
_
I
CLEARANCE T
STORM
_
J
I
/
_v _
WINDOW
INNER
ILBRACKET/'
L FRAME
SILL
I
WOOD/STRIP
I
FOR
L
BRACKET
I
I_
I
I
OUTER
%
I
SILL
INSIDE
I
I
OUTSIDE
FIG. 22
REMOVAL
FROM
WINDOW
• Turn off and unplug the air conditioner.
• Remove the front grille. See HOW TO REMOVE THE
FRONT GRILLE. Refer to page 13.
• Unscrew the side screws that you installed in Step 15.
• Slide the air conditioner out of the cabinet.
BE CAREFUL NOT TO DROP IT. Hold onto it firmly the
whole way sliding it out. Once removed, set it safety out
of the way.
• Remove the L bracket from window frame and the sash
seal from between the windows.
• Unscrew the side curtains from the window frame. Fold
them back to the sides of the cabinet.
• Remove screws attaching cabinet to inner sill. Be careful
not to let cabinet fall once screws are removed.
• Remove cabinet from window opening.
• Place air conditioner into cabinet. Reinstall side screws
and Front Grille.
• Place unit and all assembly hardware in air conditioner
shipping carton, and store in clean, dry place.
• Air conditioners covered in this manual pose an
excessive weight hazard. Two or more people
are needed to move and install the unit.
To prevent injury or strain, use proper lifting and
carrying techniques when moving unit.
• When handling the air conditioner, be careful to
avoid cuts from sharp metal fins on front and
rear coils.
• Make sure air conditioner does not fall during
removal.
-8-