Kenwood TS-870S User Manual - Page 81

Installing Options

Get Kenwood TS-870S PDF manuals and user guides View all Kenwood TS-870S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

INSTALLING OPTIONS REMOVING THE CASE TOP CASE 1 Remove the screws (10 screws). w CN901 DRU-3 Cover A q CN5 CN5 2 Lift off the top case. BOTTOM CASE 1 Remove the screws (12 screws). 4 Re-install Cover A (7 screws). 5 Replace the bottom case and re-install its screws (12 screws). VS-2 VOICE SYNTHESIZER UNIT CAUTION: Switch OFF the power and unplug the DC power cable before beginning installation. EQUIPMENT REQUIRED: • Large Phillips screwdriver • Small Phillips screwdriver 1 Confirm that the small switch on the VS-2 unit is in the "ENGLISH" position. 2 Remove the bottom case (12 screws). 3 Remove Cover A (7 screws). VS-2 2 Lift off the bottom case. DRU-3 DIGITAL RECORDING UNIT CAUTION: Switch OFF the power and unplug the DC power cable before beginning installation. Note: Refer to "INTERNAL ADJUSTMENTS" {page 70} for information on adjusting the recording level. EQUIPMENT REQUIRED: • Large Phillips screwdriver • Small Phillips screwdriver 1 Remove the bottom case (12 screws). 2 Remove Cover A (see diagram) (7 screws). 3 Locate the CN5 connector in the transceiver. Remove the paper backing from one side of the supplied cushion, then install the cushion. Remove the paper backing from the other side of the installed cushion, then plug the DRU-3 connector (CN901) into CN5. ENGLISH Cover A CN6 4 Locate the CN6 cable in the transceiver, and plug this cable into the VS-2 unit. Threaded post CN6 VS-2 Threaded post 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
75
VS-2
ENGLISH
CN6
Cover A
INSTALLING OPTIONS
REMOVING THE CASE
TOP CASE
1
Remove the screws (10 screws).
2
Lift off the top case.
BOTTOM CASE
1
Remove the screws (12 screws).
2
Lift off the bottom case.
DRU-3 DIGITAL RECORDING UNIT
CAUTION:
Switch OFF the power and unplug the DC power cable
before beginning installation.
Note:
Refer to “INTERNAL ADJUSTMENTS” {page 70} for
information on adjusting the recording level.
EQUIPMENT REQUIRED
:
•
Large Phillips screwdriver
•
Small Phillips screwdriver
1
Remove the bottom case (12 screws).
2
Remove Cover A (see diagram) (7 screws).
3
Locate the CN5 connector in the transceiver.
Remove the paper backing from one side of the
supplied cushion, then install the cushion.
Remove
the paper backing from the other side of the installed
cushion, then plug the DRU-3 connector (CN901)
into CN5.
4
Re-install Cover A (7 screws).
5
Replace the bottom case and re-install its screws
(12 screws).
VS-2 VOICE SYNTHESIZER UNIT
CAUTION:
Switch OFF the power and unplug the DC power cable
before beginning installation.
EQUIPMENT REQUIRED:
•
Large Phillips screwdriver
•
Small Phillips screwdriver
1
Confirm that the small switch on the VS-2 unit is in
the
“
ENGLISH
”
position.
2
Remove the bottom case (12 screws).
3
Remove Cover A (7 screws).
4
Locate the CN6 cable in the transceiver, and plug
this cable into the VS-2 unit.
CN5
CN5
q
CN901
DRU-3
w
Cover A
VS-2
CN6
Threaded
post
Threaded
post