Kenwood TS-870S User Manual - Page 91

For- ɹma
t Name No. No. of Digits Format 42 KEYER SPEED Represented in words 3 per minute using 001 (min.)~100 (max.). 43 KEYER MESSAGE Contains the CW 24 message. 44 KEYER BUFFER 0: Buffer space 1 available 1: Buffer space not available 45 LOAD MESSAGE 1 0: Not recording. A Set command cancels recording. 1: Channel 1 2: Channel 2 3: Channel 3 4: Channel 4 46 LEVEL Represented using 000 3 (min.)~255 (max.). 47 POWER CONTROL Represented in watts 3 using 010 (min.)~ 100 (max.). 48 RF ATTENUATOR 00: 0 dB 2 01: 6 dB 02: 12 dB 03: 18 dB 49 SEMI BREAK-IN DELAY TIME Represented in msec 4 using 0050~0800. 50 SYSTEM RESET 1: VFO Reset 1 ([RX A]+[ ]) 2: MR Reset ([A=B]+[ ]) 51 VOX DELAY TIME Represented in msec 4 using 0150~2700. SUBTONE TABLE FOR FORMAT NO.14 No. Freq. (Hz) Freq. No. (Hz) No. Freq. (Hz) No. Freq. (Hz) 01 67.0 11 97.4 21 136.5 31 192.8 02 71.9 12 100.0 22 141.3 32 203.5 03 74.4 13 103.5 23 146.2 33 210.7 04 77.0 14 107.2 24 151.4 34 218.1 05 79.7 15 110.9 25 156.7 35 225.7 06 82.5 16 114.8 26 162.2 36 233.6 07 85.4 17 118.8 27 167.9 37 241.8 08 88.5 18 123.0 28 173.8 38 250.3 09 91.5 19 127.3 29 179.9 39 1750 10 94.8 20 131.8 30 186.2 TERMINATOR To signal the end of a command, it is necessary to use a semicolon (;). The digit where this special character must appear differs depending on commands. APPENDICES ● TYPES OF COMMANDS Commands can be classified as shown below: Commands Input Command (Input to the transceiver) Output Command (From the transceiver) Set Command (Sets a particular condition.) Read Command (Reads an answer.) Answer Command (Transmits a condition.) For example, note the following in the case of the FA command (Frequency of VFO A): • To set the frequency to 7 MHz, the following command is sent from the computer to the transceiver: "FA00007000000;" (Set Command) • To read the frequency of VFO A, the following command is sent from the computer to the transceiver: "FA;" (Read Command) • When the Read Command above has been sent, the following command is returned to the computer: "FA00007000000;" (Answer Command) COMPUTER CONTROL COMMANDS A summary of the command library for communication between a computer and the TS-870S is included in this section. This information can be used if you are developing your own transceiver control program, or you are troubleshooting an existing control application. Command Function AC Antenna Tuner THRU/IN-LINE, and tuning START/CANCEL AG Sets or reads AF gain. AI Auto information (OFF/ON) AN Selects antenna connector (ANT 1/ ANT 2). BC Sets or reads Beat Cancel. BI Sets or reads CW Break-in. BY Reads Busy signals. CG Sets or reads carrier gain. DN MIC DOWN function EQ Sets or reads Transmit Equalizer. EX Sets or reads Menu. FA Sets or reads VFO A frequency. 85