Kenwood TS-870S User Manual - Page 95
Reading Command Tables, Command Tables
View all Kenwood TS-870S manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 95 highlights
READING COMMAND TABLES w q AC ANTENNA TUNER CONTROL u io APPENDICES ● !0 Answer Read Set Function Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL e Parameter Format Parameter function P1 30 TUNE THRU/IN (Answer Only) P2 30 TUNE THRU/IN r 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AC P2 P3 ; P3 1 TUNE OFF/ON Input 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Note: t AC ; P1 is used for Answer only. Tuning cannot be started if P2 is in the 1 2 3 4 5 6 7 8 9 10 11 12 13 14 THRU state (If P2="0", selecting "1" for P3 y A C P1 P2 P3 ; does not start tuning). P1: RX THRU/IN P2: TX THRU/IN Output q Command w Name e Function of the command r The format of the command is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Set command. t The format of the command for reading the transceiver's current status is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Read command. y The format of the command output from the transceiver is shown. When oblique lines are drawn in the 1st and 2nd columns, there is no Answer command. u The number of command digits is shown. i Corresponds to the parameter of the command format. o Corresponds to the Format number in the Parameter Table. For the parameter formats, refer to the Parameter Table {page 84}. !0 Indicates the function of the parameter. COMMAND TABLES Note: Parameters that have a Parameter Function of "NOT USED" are not supported by the TS-870S. Any character except the ASCII control codes (00 to 1Fh) and the terminator (;) may be entered for those parameters. Function AC ANTENNA TUNER CONTROL Antenna Tuner THRU/IN -LINE, and tuning START/CANCEL Parameter Format Parameter function P1 30 TUNE THRU/IN (Answer Only) Set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A C P2 P3 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AC ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A C P1 P2 P3 ; P2 30 TUNE THRU/IN P3 1 TUNE OFF/ON Note: P1 is used for Answer only. Tuning cannot be started if P2 is in the THRU state (If P2="0", selecting "1" for P3 does not start tuning). P1: RX THRU/IN P2: TX THRU/IN Output Input Function AI AUTO INFORMATION Parameter Format Parameter function Auto information OFF/ON P1 32 AI NUMBER Set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A I P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AI ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A I P1 ; Note: For other commands, controls whether changing a parameter will or will not trigger the corresponding Answer command to be output. Ex: For IF, the Answer command is output if the step frequency or RIT/XIT frequency is changed. Input Answer Read Answer Read Output Function AG AF GAIN Sets or reads AF gain. Parameter Format Parameter function P1 31 AF GAIN Set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A G P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AG ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A G P1 ; Input Function AN ANTENNA NUMBER Selects antenna connector ANT 1/ ANT 2. Parameter Format Parameter function P1 33 ANTENNA NUMBER Set 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A N P1 ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AN ; 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A N P1 ; Input Answer Read Answer Read Output Output 89