Konica Minolta AccurioPress C14000 Plockmatic SD-350/SD-500 System Operator Ma - Page 76

BookFold Module fault codes, BookFold Module, Cover Feeder, continues

Get Konica Minolta AccurioPress C14000 PDF manuals and user guides View all Konica Minolta AccurioPress C14000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Cover Feeder fault codes, continues Cover Feeder, continues Code / message Cover stack is low, please add covers! Explanation / action Indicates that the Cover Feeder is almost out of Covers. There are two ways to continue operation. 1. Loading more cover sheets: Load more cover sheets according to section 2, "Making Booklets" and press the [Done] button. The message will extinguish and copier will start. 2. Using up the remaining cover sheets that are loaded: Press the [Dismiss] button. The message will extinguish and copier will start. Load covers! 6 NOTE: Be aware that if you use alternative 2, the system will hard stop i.e. without completing the cycle when there is no covers left. Message is displayed when covers are empty. Message will also be displayed if the green [check] button was pressed after deciding to use Covers but before the bin was loaded. There are two ways to continue operation. 1. If you wish to continue production: Load cover sheets according to section 2, "Making Booklets." and press the [Done] button. The message will extinguish and copier will start. 2. If cover job is finished and you wish to run a new job without covers: Select Cover Off in the Cover menu. BookFold Module fault codes BookFold Module Code / message BF-001 - BF-151 Possible fault in area, please power off and power on to recover! BF-201 - BF-206 Clear misfeed Explanation / action Indicates that there might be an internal communication error. Power off and on the system. If problem persists, contact customer support. A misfeed has occurred in the BookFold Module. If problem persists, clean feed belts according to section 7, "REMARKS." Check that the pressure on the upper feed belts is set to the default position. The pressure springs should always be at its upper position where the pressure is equal to its highest value. See section 7, "REMARKS." 76

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
76
6
BookFold Module
Code / message
Explanation / action
BF-001 - BF-151 Possible fault in area,
please power off and power on to
recover!
Indicates that there might be an internal communication
error. Power off and on the system. If problem persists,
contact customer support.
BF-201 - BF-206 Clear misfeed
A misfeed has occurred in the BookFold Module.
If problem persists, clean feed belts according to section
7, “REMARKS.”
Check that the pressure on the upper feed belts is set to
the default position. The pressure springs should always
be at its upper position where the pressure is equal to its
highest value. See section 7, “REMARKS.”
BookFold Module fault codes
Cover Feeder, continues
Code / message
Explanation / action
Cover stack is low, please add covers!
Indicates that the Cover Feeder is almost out of Covers.
There are two ways to continue operation.
1. Loading more cover sheets:
Load more cover sheets according to section 2,
“Making Booklets” and press the [Done] button. The
message will extinguish and copier will start.
2.
Using up the remaining cover sheets that are
loaded:
Press the [Dismiss] button. The message will
extinguish and copier will start.
NOTE:
Be aware that if you use alternative 2, the system will
hard stop i.e. without completing the cycle when there is
no covers left.
Load covers!
Message is displayed when covers are empty. Message
will also be displayed if the green [check] button was
pressed after deciding to use Covers but before the bin
was loaded.
There are two ways to continue operation.
1.
If you wish to continue production:
Load cover sheets according to section 2, “Making
Booklets.” and press the [Done] button. The
message will extinguish and copier will start.
2.
If cover job is finished and you wish to run a new job
without covers:
Select Cover Off in the Cover menu.
Cover Feeder fault codes, continues