Home » Konica Minolta Manuals » Printers » Konica Minolta KIP 9900 » Manual Viewer

Konica Minolta KIP 9900 User Guide - Page 138

Cleaning the LED Head, Press the EXP-CLEAN Key on the Operation Panel.

View all Konica Minolta KIP 9900 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

3. 6. 2 Cleaning the LED Head Sometimes a clear black thin line may run vertically on the printout as the following example. This defective image is possibly caused by the dirt of LED Head, and may be fixed if cleaning is performed. Correct print When the LED Head is dirty ; 1. Press the EXP-CLEAN Key on the Operation Panel. PAPER DECK MF 1234 D1 WIRE CLEAN EXP- CLEAN SELECT CUT D2 D3 EXIT PF D4 COPY DENSITY MENU ENTER ONLINE EXP- CLEAN Key 2. Cleaning is started, and the Ready Indicator flashes during the cleaning. It will take about 2 minutes for the cleaning. The Ready Indicator stops flashing when cleaning is finished. PAPER DECK MF 1234 D1 WIRE CLEAN EXP- CLEAN SELECT CUT D2 D3 Ready Indicator EXIT PF D4 COPY DENSITY MENU ENTER ONLINE 3-34 Chapter 3 Error Correction & Maintenance

Section	Page
KIP 9900 Hardware Operation Guide	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 5 Appearance	14
1.5.1 Front view	14
1.5.2 Right side view	15
1.5.3 Rear view	16
1.5.4 Operation Panel	19
1.5.5 Media Indicators	20
1.5.6 “in use” Indicators	21
Chapter 2 Basic Operations	23
2. 1 Turning on the KIP 9900	24
2. 2 Turning off the KIP 9900	26
2. 3 Setting the Roll Media into Roll Deck	27
2. 3. 1 Roll 1 / 2 / 3	28
2. 3. 2 Roll 4	35
2. 4 Setting Cut Sheet Media to Bypass Feeder	38
2. 4. 1 Multi-feeding of cut sheet media	39
2. 4. 2 Singular feeding of cut sheet media	40
2. 5 Replacing the Toner Cartridge	42
2. 6 Dehumidifying the Roll Media	46
2. 7 Initial Cut (Straighten the leading edge of roll media)	48
2. 8 User Mode	50
2. 8. 1 User Mode 1 (Test Print)	52
2. 8. 2 User Mode 2 (Calendar setting)	54
2. 8. 3 User Mode 3 (Warm Sleep Mode ON / OFF & timer setting)	59
2. 8. 4 User Mode 4 (Cold Sleep Mode timer setting)	63
2. 8. 5 User Mode 5 (Automatic paper cut at power ON)	66
2. 8. 6 User Mode 6 (Transfer Support LED ON/OFF [Film])	69
2. 8. 7 User Mode 7 (Alarm ON / OFF)	72
2. 8. 8 User Mode 8 (Choice of Standard / Special Print Mode [Plain paper])	75
2. 8. 9 User Mode 9 (Choice of Standard / Special Print Mode [Tracing paper])	79
2. 8.10 User Mode A (Choice of Standard / Special Print Mode [Film])	82
2. 8.11 User Mode B (Selection of Image Enhancement Mode)	85
2. 8.12 User Mode D (Cancel E-26 error)	88
2. 8.13 User Mode E (Cancel E-28 error)	91
2. 8.14 User Mode A1 (Auto Initial Cut: Media)	94
2. 8.15 User Mode A2 (Auto Initial Cut: Length)	94
2. 8.16 User Mode P1 to P4 (Special Width Selection in Metric Mode)	95
2. 8.17 User Mode F0 to Fb (Fold settings)	98
Chapter 3 Error Correction and Maintenance	105
3. 1 Media Mis-feed Errors (J-**)	106
3. 1. 1 Mis-feed in Roll Decks (J-01, J-02, J-03 & J-04)	107
3. 1. 2 Mis-feed in the Bypass Feeder (J-05)	110
3. 1. 3 Mis-feed between Cutter and Drum (J-11)	111
3. 1. 4 Mis-feed on Internal Transportation Unit (J-12) and Fuser Entrance (J-13)	115
3. 1. 5 Mis-feed in Fuser Unit (J-14)	122
3. 1. 6 Mis-feed in Folder (J-21)	129
3. 1. 7 Mis-feed in Auto Stacker (J-22)	129
3. 2 Open Errors (U-**)	130
3. 2. 1 Top Drawer Open (U-01)	130
3. 2. 2 Middle Drawer Open (U-02)	130
3. 2. 3 Bottom Drawer Open (U-03)	131
3. 2. 4 Internal Transportation Unit Open (U-04)	131
3. 2. 5 Toner Cover Open (U-06)	131
3. 2. 6 Bypass Feeder Open (U-11)	132
3. 2. 7 Right Side Door Open (U-12)	132
3. 2. 8 Top Rear Cover Open (U-13)	132
3. 2. 9 Exit Cover Open (U-14)	133
3. 2.10 Folder Door Open (U-21)	133
3. 3 Toner Cartridge Error (C-01)	134
3. 4 Service Call Errors (E-**)	135
3. 5 Interruption of Print by Temperature Control	136
3. 6 Maintenance	137
3. 6. 1 Cleaning the Image Corona	137