Home » Konica Minolta Manuals » Printers » Konica Minolta KIP 9900 » Manual Viewer

Konica Minolta KIP 9900 User Guide - Page 40

Singular feeding of cut sheet media - guide

View all Konica Minolta KIP 9900 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2. 4. 2 Singular feeding of cut sheet media Larger cut sheet media than A2 (594mm) or 24" can be fed into KIP 9900 by singular feeding only. NOTE Do not leave the cut sheet media on the Bypass Feeder for a long time as it will get moisture. Such media will result in mis-feed or defective image. (Keep the media in a plastic bad to block the moisture.) 1. Select the bypass feeding mode on the outer device. 2. Slide the Cut Sheet Guides and place at the requested size guides. Cut Sheet Guide 3. Put the media on the Bypass Feeder and move it forward until the leading edge contacts the feeding roller. Feeding roller 2-18 Chapter 2 Basic Operations

Section	Page
KIP 9900 Hardware Operation Guide	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 5 Appearance	14
1.5.1 Front view	14
1.5.2 Right side view	15
1.5.3 Rear view	16
1.5.4 Operation Panel	19
1.5.5 Media Indicators	20
1.5.6 “in use” Indicators	21
Chapter 2 Basic Operations	23
2. 1 Turning on the KIP 9900	24
2. 2 Turning off the KIP 9900	26
2. 3 Setting the Roll Media into Roll Deck	27
2. 3. 1 Roll 1 / 2 / 3	28
2. 3. 2 Roll 4	35
2. 4 Setting Cut Sheet Media to Bypass Feeder	38
2. 4. 1 Multi-feeding of cut sheet media	39
2. 4. 2 Singular feeding of cut sheet media	40
2. 5 Replacing the Toner Cartridge	42
2. 6 Dehumidifying the Roll Media	46
2. 7 Initial Cut (Straighten the leading edge of roll media)	48
2. 8 User Mode	50
2. 8. 1 User Mode 1 (Test Print)	52
2. 8. 2 User Mode 2 (Calendar setting)	54
2. 8. 3 User Mode 3 (Warm Sleep Mode ON / OFF & timer setting)	59
2. 8. 4 User Mode 4 (Cold Sleep Mode timer setting)	63
2. 8. 5 User Mode 5 (Automatic paper cut at power ON)	66
2. 8. 6 User Mode 6 (Transfer Support LED ON/OFF [Film])	69
2. 8. 7 User Mode 7 (Alarm ON / OFF)	72
2. 8. 8 User Mode 8 (Choice of Standard / Special Print Mode [Plain paper])	75
2. 8. 9 User Mode 9 (Choice of Standard / Special Print Mode [Tracing paper])	79
2. 8.10 User Mode A (Choice of Standard / Special Print Mode [Film])	82
2. 8.11 User Mode B (Selection of Image Enhancement Mode)	85
2. 8.12 User Mode D (Cancel E-26 error)	88
2. 8.13 User Mode E (Cancel E-28 error)	91
2. 8.14 User Mode A1 (Auto Initial Cut: Media)	94
2. 8.15 User Mode A2 (Auto Initial Cut: Length)	94
2. 8.16 User Mode P1 to P4 (Special Width Selection in Metric Mode)	95
2. 8.17 User Mode F0 to Fb (Fold settings)	98
Chapter 3 Error Correction and Maintenance	105
3. 1 Media Mis-feed Errors (J-**)	106
3. 1. 1 Mis-feed in Roll Decks (J-01, J-02, J-03 & J-04)	107
3. 1. 2 Mis-feed in the Bypass Feeder (J-05)	110
3. 1. 3 Mis-feed between Cutter and Drum (J-11)	111
3. 1. 4 Mis-feed on Internal Transportation Unit (J-12) and Fuser Entrance (J-13)	115
3. 1. 5 Mis-feed in Fuser Unit (J-14)	122
3. 1. 6 Mis-feed in Folder (J-21)	129
3. 1. 7 Mis-feed in Auto Stacker (J-22)	129
3. 2 Open Errors (U-**)	130
3. 2. 1 Top Drawer Open (U-01)	130
3. 2. 2 Middle Drawer Open (U-02)	130
3. 2. 3 Bottom Drawer Open (U-03)	131
3. 2. 4 Internal Transportation Unit Open (U-04)	131
3. 2. 5 Toner Cover Open (U-06)	131
3. 2. 6 Bypass Feeder Open (U-11)	132
3. 2. 7 Right Side Door Open (U-12)	132
3. 2. 8 Top Rear Cover Open (U-13)	132
3. 2. 9 Exit Cover Open (U-14)	133
3. 2.10 Folder Door Open (U-21)	133
3. 3 Toner Cartridge Error (C-01)	134
3. 4 Service Call Errors (E-**)	135
3. 5 Interruption of Print by Temperature Control	136
3. 6 Maintenance	137
3. 6. 1 Cleaning the Image Corona	137