Konica Minolta KIP 9900 User Guide - Page 33

Positioning Hole, Do not feed any media with tape or adhesive remaining on it.

Get Konica Minolta KIP 9900 PDF manuals and user guides View all Konica Minolta KIP 9900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

7. Using a slit on each drawer, cut off the leading part of roll media with a cutter knife to straighten the leading edge. Slit NOTE Do not feed any media with tape or adhesive remaining on it. It is recommended to trim at least one full revolution from the roll when installing a new roll. 8. Insert the leading edge of media between feeding rollers, and rotate the upper feeding roller to pinch the leading edge (10 - 20mm) with the rollers. Feeding rollers NOTE The Roll Deck 3 only has a positioning hole. (Other Rolls do not have it.) Feed the roll media until its leading edge comes to appear in the hole, and place the leading edge at the center of the hole. Positioning Hole 2-11 Chapter 2 Basic Operations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Chapter 2
Basic Operations
2-11
7.
Using a slit on each drawer, cut off the leading part of roll media with a cutter knife to straighten
the leading edge.
8.
Insert the leading edge of media between feeding rollers, and rotate the upper feeding roller to
pinch the leading edge (10 - 20mm) with the rollers.
NOTE
Do not feed any media with tape or adhesive remaining on it.
It is recommended to trim
at least one full revolution from the roll when installing a new roll.
NOTE
The Roll Deck 3 only has a positioning hole. (Other Rolls do not have it.)
Feed the roll media until its leading edge comes to appear in the hole, and place the
leading edge at the center of the hole.
Positioning Hole
Slit
Feeding rollers