Home » Konica Minolta Manuals » Printers » Konica Minolta KIP 9900 » Manual Viewer

Konica Minolta KIP 9900 User Guide - Page 47

Dehumidify Heater Switch, The user

View all Konica Minolta KIP 9900 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

2. There is a Dehumidify Heater Switch on the right. Press "H" to turn on the Dehumidify Heater, and press "L" to turn it off. Dehumidify Heater Switch Reference (1) The KIP 9900 offers some kinds of operation mode of Dehumidify Heater, which specify when the heater should work. Your service personnel select the best operation mode at machine installation considering your usage environment. If "creasing" or "image void" starts to occur so frequently when the usage environment changes (because of seasonal reason and etc) during normal use, it may be fixed if the operation mode is changed to other ones. Consult your service personnel in such case. (User can not change the mode.) (2) The KIP 9900 must be plugged into the outlet for operating the Dehumidify Heater. (Some operation mode enables the Dehumidify Heater to work even if the KIP 9900 is turned off at night if only it is plugged in. Do not plug out the KIP 9900 in such case especially.) (3) Dehumidify Heater is just a possibility to fix "creasing" or "image void", but it is NOT the complete solution for such defects. If the media has been already humidified before installed to the Roll Deck, it will be no use in turning on the Dehumidify Heater. The user needs to take great care for preventing the printing media from being humidified. • Do not unpack the media until right before it is to be installed to the machine. • When the air is much humidified, do not leave the roll media in the deck. Remove it from the deck, put it in a plastic bag and close firmly to avoid the humidity. 2-25 Chapter 2 Basic Operations

Section	Page
KIP 9900 Hardware Operation Guide	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 5 Appearance	14
1.5.1 Front view	14
1.5.2 Right side view	15
1.5.3 Rear view	16
1.5.4 Operation Panel	19
1.5.5 Media Indicators	20
1.5.6 “in use” Indicators	21
Chapter 2 Basic Operations	23
2. 1 Turning on the KIP 9900	24
2. 2 Turning off the KIP 9900	26
2. 3 Setting the Roll Media into Roll Deck	27
2. 3. 1 Roll 1 / 2 / 3	28
2. 3. 2 Roll 4	35
2. 4 Setting Cut Sheet Media to Bypass Feeder	38
2. 4. 1 Multi-feeding of cut sheet media	39
2. 4. 2 Singular feeding of cut sheet media	40
2. 5 Replacing the Toner Cartridge	42
2. 6 Dehumidifying the Roll Media	46
2. 7 Initial Cut (Straighten the leading edge of roll media)	48
2. 8 User Mode	50
2. 8. 1 User Mode 1 (Test Print)	52
2. 8. 2 User Mode 2 (Calendar setting)	54
2. 8. 3 User Mode 3 (Warm Sleep Mode ON / OFF & timer setting)	59
2. 8. 4 User Mode 4 (Cold Sleep Mode timer setting)	63
2. 8. 5 User Mode 5 (Automatic paper cut at power ON)	66
2. 8. 6 User Mode 6 (Transfer Support LED ON/OFF [Film])	69
2. 8. 7 User Mode 7 (Alarm ON / OFF)	72
2. 8. 8 User Mode 8 (Choice of Standard / Special Print Mode [Plain paper])	75
2. 8. 9 User Mode 9 (Choice of Standard / Special Print Mode [Tracing paper])	79
2. 8.10 User Mode A (Choice of Standard / Special Print Mode [Film])	82
2. 8.11 User Mode B (Selection of Image Enhancement Mode)	85
2. 8.12 User Mode D (Cancel E-26 error)	88
2. 8.13 User Mode E (Cancel E-28 error)	91
2. 8.14 User Mode A1 (Auto Initial Cut: Media)	94
2. 8.15 User Mode A2 (Auto Initial Cut: Length)	94
2. 8.16 User Mode P1 to P4 (Special Width Selection in Metric Mode)	95
2. 8.17 User Mode F0 to Fb (Fold settings)	98
Chapter 3 Error Correction and Maintenance	105
3. 1 Media Mis-feed Errors (J-**)	106
3. 1. 1 Mis-feed in Roll Decks (J-01, J-02, J-03 & J-04)	107
3. 1. 2 Mis-feed in the Bypass Feeder (J-05)	110
3. 1. 3 Mis-feed between Cutter and Drum (J-11)	111
3. 1. 4 Mis-feed on Internal Transportation Unit (J-12) and Fuser Entrance (J-13)	115
3. 1. 5 Mis-feed in Fuser Unit (J-14)	122
3. 1. 6 Mis-feed in Folder (J-21)	129
3. 1. 7 Mis-feed in Auto Stacker (J-22)	129
3. 2 Open Errors (U-**)	130
3. 2. 1 Top Drawer Open (U-01)	130
3. 2. 2 Middle Drawer Open (U-02)	130
3. 2. 3 Bottom Drawer Open (U-03)	131
3. 2. 4 Internal Transportation Unit Open (U-04)	131
3. 2. 5 Toner Cover Open (U-06)	131
3. 2. 6 Bypass Feeder Open (U-11)	132
3. 2. 7 Right Side Door Open (U-12)	132
3. 2. 8 Top Rear Cover Open (U-13)	132
3. 2. 9 Exit Cover Open (U-14)	133
3. 2.10 Folder Door Open (U-21)	133
3. 3 Toner Cartridge Error (C-01)	134
3. 4 Service Call Errors (E-**)	135
3. 5 Interruption of Print by Temperature Control	136
3. 6 Maintenance	137
3. 6. 1 Cleaning the Image Corona	137

Match case Limit results 1 per page

Chapter 2

Basic Operations

2-25

There is a Dehumidify Heater Switch on the right.

Press “H” to turn on the Dehumidify Heater, and press “L” to turn it off.

(1) The KIP 9900 offers some kinds of operation mode of Dehumidify Heater, which specify

when the heater should work. Your service personnel select the best operation mode at

machine installation considering your usage environment. If “creasing” or “image void”

starts to occur so frequently when the usage environment changes (because of seasonal

reason and etc) during normal use, it may be fixed if the operation mode is changed to

other ones. Consult your service personnel in such case. (User can not change the mode.)

(2) The KIP 9900 must be plugged into the outlet for operating the Dehumidify Heater. (Some

operation mode enables the Dehumidify Heater to work even if the KIP 9900 is turned off

at night if only it is plugged in. Do not plug out the KIP 9900 in such case especially.)

(3) Dehumidify Heater is just a possibility to fix “creasing” or “image void”, but it is NOT the

complete solution for such defects.

If the media has been already humidified before

installed to the Roll Deck, it will be no use in turning on the Dehumidify Heater.

The user

needs to take great care for preventing the printing media from being humidified.

•

Do not unpack the media until right before it is to be installed to the machine.

•

When the air is much humidified, do not leave the roll media in the deck. Remove it

from the deck, put it in a plastic bag and close firmly to avoid the humidity.

Reference

Dehumidify Heater Switch