Home » Konica Minolta Manuals » Printers » Konica Minolta KIP 9900 » Manual Viewer

Konica Minolta KIP 9900 User Guide - Page 22

Reference

View all Konica Minolta KIP 9900 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Reference Even if the KIP 9900 is printing, it is possible to open the drawer and replace/install the roll media without interrupting the print operation. However, it is not necessarily allowed to open any drawer at any time. A certain drawer can not be opened in the following situations. 1. When the roll media is fed from that drawer, this drawer can not be opened. 2. When the media (including cut sheet media) fed from other drawer is passing through the media path in a certain drawer, this drawer can not be opened. See the following section diagram. Media feeding paths from each Roll Deck is integrated into one path in the middle drawer. When the KIP 9900 is printing with the roll media fed from the Roll Deck 1 for example, only the bottom drawer can be opened. ("in use" Indicators for top and middle drawers will light orange in this case.) Top Drawer is not allowed to open. in use Middle Drawer is not allowed to open. in use Bottom Drawer is allowed to open. in use Roll Deck 1 Roll Deck 2 Roll Deck 4 Roll Deck 3 D4 1-14 Chapter 1 Before Use

Section	Page
KIP 9900 Hardware Operation Guide	4
WARNING	5
CAUTION	6
POWER CORD INSTRUCTION	7
Chapter 1 Before Use	8
1. 1 Installation Requirements	9
1. 2 Originals Prohibited from Duplication	10
1. 3 Features	11
1. 4 Specifications	12
1. 5 Appearance	14
1.5.1 Front view	14
1.5.2 Right side view	15
1.5.3 Rear view	16
1.5.4 Operation Panel	19
1.5.5 Media Indicators	20
1.5.6 “in use” Indicators	21
Chapter 2 Basic Operations	23
2. 1 Turning on the KIP 9900	24
2. 2 Turning off the KIP 9900	26
2. 3 Setting the Roll Media into Roll Deck	27
2. 3. 1 Roll 1 / 2 / 3	28
2. 3. 2 Roll 4	35
2. 4 Setting Cut Sheet Media to Bypass Feeder	38
2. 4. 1 Multi-feeding of cut sheet media	39
2. 4. 2 Singular feeding of cut sheet media	40
2. 5 Replacing the Toner Cartridge	42
2. 6 Dehumidifying the Roll Media	46
2. 7 Initial Cut (Straighten the leading edge of roll media)	48
2. 8 User Mode	50
2. 8. 1 User Mode 1 (Test Print)	52
2. 8. 2 User Mode 2 (Calendar setting)	54
2. 8. 3 User Mode 3 (Warm Sleep Mode ON / OFF & timer setting)	59
2. 8. 4 User Mode 4 (Cold Sleep Mode timer setting)	63
2. 8. 5 User Mode 5 (Automatic paper cut at power ON)	66
2. 8. 6 User Mode 6 (Transfer Support LED ON/OFF [Film])	69
2. 8. 7 User Mode 7 (Alarm ON / OFF)	72
2. 8. 8 User Mode 8 (Choice of Standard / Special Print Mode [Plain paper])	75
2. 8. 9 User Mode 9 (Choice of Standard / Special Print Mode [Tracing paper])	79
2. 8.10 User Mode A (Choice of Standard / Special Print Mode [Film])	82
2. 8.11 User Mode B (Selection of Image Enhancement Mode)	85
2. 8.12 User Mode D (Cancel E-26 error)	88
2. 8.13 User Mode E (Cancel E-28 error)	91
2. 8.14 User Mode A1 (Auto Initial Cut: Media)	94
2. 8.15 User Mode A2 (Auto Initial Cut: Length)	94
2. 8.16 User Mode P1 to P4 (Special Width Selection in Metric Mode)	95
2. 8.17 User Mode F0 to Fb (Fold settings)	98
Chapter 3 Error Correction and Maintenance	105
3. 1 Media Mis-feed Errors (J-**)	106
3. 1. 1 Mis-feed in Roll Decks (J-01, J-02, J-03 & J-04)	107
3. 1. 2 Mis-feed in the Bypass Feeder (J-05)	110
3. 1. 3 Mis-feed between Cutter and Drum (J-11)	111
3. 1. 4 Mis-feed on Internal Transportation Unit (J-12) and Fuser Entrance (J-13)	115
3. 1. 5 Mis-feed in Fuser Unit (J-14)	122
3. 1. 6 Mis-feed in Folder (J-21)	129
3. 1. 7 Mis-feed in Auto Stacker (J-22)	129
3. 2 Open Errors (U-**)	130
3. 2. 1 Top Drawer Open (U-01)	130
3. 2. 2 Middle Drawer Open (U-02)	130
3. 2. 3 Bottom Drawer Open (U-03)	131
3. 2. 4 Internal Transportation Unit Open (U-04)	131
3. 2. 5 Toner Cover Open (U-06)	131
3. 2. 6 Bypass Feeder Open (U-11)	132
3. 2. 7 Right Side Door Open (U-12)	132
3. 2. 8 Top Rear Cover Open (U-13)	132
3. 2. 9 Exit Cover Open (U-14)	133
3. 2.10 Folder Door Open (U-21)	133
3. 3 Toner Cartridge Error (C-01)	134
3. 4 Service Call Errors (E-**)	135
3. 5 Interruption of Print by Temperature Control	136
3. 6 Maintenance	137
3. 6. 1 Cleaning the Image Corona	137

Match case Limit results 1 per page

Chapter 1

Before Use

1-14

Even if the KIP 9900 is printing, it is possible to open the drawer and replace/install the roll

media without interrupting the print operation. However, it is not necessarily allowed to open

any drawer at any time. A certain drawer can not be opened in the following situations.

When the roll media is fed from that drawer, this drawer can not be opened.

When the media (including cut sheet media) fed from other drawer is passing through the

media path in a certain drawer, this drawer can not be opened.

See the following section diagram. Media feeding paths from each Roll Deck is integrated into

one path in the middle drawer. When the KIP 9900 is printing with the roll media fed from the

Roll Deck 1 for example, only the bottom drawer can be opened. (“in use” Indicators for top

and middle drawers will light orange in this case.)

in use

Top Drawer is not

allowed to open.

Middle Drawer is not

allowed to open.

Bottom Drawer is

allowed to open.

Roll Deck 1

Roll Deck 2

Roll Deck 3

Roll Deck 4

Reference