Lantronix EDS1100 EDS1100 / EDS2100 - User Guide - Page 104

Protocol Stack Settings, TCP Settings

Get Lantronix EDS1100 PDF manuals and user guides View all Lantronix EDS1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

13: Maintenance and Diagnostics Settings Protocol Stack Settings In the Protocol Stack web page, you can configure TCP, IP, ICMP, SMTP and ARP. TCP Settings To configure the TCP network protocol: 1. Click Protocol Stack on the menu bar. 2. Click TCP. Figure 13-4 TCP Protocol 3. Modify the following settings: Table 13-5 TCP Settings Protocol Stack TCP Settings Send RSTs Ack Limit Send Data Description Click Enabled to send RSTs or Disabled to stop sending RSTs. TCP contains six control bits, with one or more defined in each packet. RST is one of the control bits. The RST bit is responsible for telling the receiving TCP stack to end a connection immediately. Note: Setting the RSTs may pose a security risk. Enter a number to limit how many packets get received before an ACK gets forced. If there is a large amount of data to acknowledge, an ACK gets forced. If the sender TCP implementation waits for an ACK before sending more data even though the window is open, setting the Ack Limit to 1 packet improves performance by forcing immediate acknowledgements. The Send Data selection governs when data may be sent into the network. The Standard implementation waits for an ACK before sending a packet less than the maximum length. Select Expedited to send data whenever the window allows it. EDS1100/2100 User Guide 104

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
13: Maintenance and Diagnostics Settings
EDS1100/2100 User Guide
104
Protocol Stack Settings
In the Protocol Stack web page, you can configure TCP, IP, ICMP, SMTP and ARP.
TCP Settings
To configure the TCP network protocol:
1.
Click
Protocol Stack
on the menu bar.
2.
Click
TCP
.
Figure 13-4
TCP Protocol
3.
Modify the following settings:
Table 13-5
TCP Settings
Protocol Stack
TCP Settings
Description
Send RSTs
Click
Enabled
to send RSTs or
Disabled
to stop sending RSTs. TCP
contains six control bits, with one or more defined in each packet. RST is one
of the control bits. The RST bit is responsible for telling the receiving TCP
stack to end a connection immediately.
Note:
Setting the RSTs may pose a security risk.
Ack Limit
Enter a number to limit how many packets get received before an ACK gets
forced. If there is a large amount of data to acknowledge, an ACK gets
forced. If the sender TCP implementation waits for an ACK before sending
more data even though the window is open, setting the
Ack Limit
to 1
packet
improves performance by forcing immediate acknowledgements.
Send Data
The
Send Data
selection governs when data may be sent into the network.
The Standard implementation waits for an ACK before sending a packet less
than the maximum length. Select Expedited to send data whenever the
window allows it.