Lantronix EDS1100 EDS1100 / EDS2100 - User Guide - Page 72

SNMP Settings, To con SNMP

Get Lantronix EDS1100 PDF manuals and user guides View all Lantronix EDS1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

10: Service Settings SNMP Settings Simple Network Management Protocol (SNMP) is a network management tool that monitors network devices for conditions that need attention. The SNMP service responds to SNMP requests and generates SNMP Traps. This page is used to configure the SNMP agent. To configure SNMP: 1. Click SNMP on the menu bar. The SNMP page opens and shows the current SNMP configuration. Figure 10-4 SNMP Configuration 2. Enter or modify the following settings: SNMP Settings State Read Community Write Community System Contact System Name System Description System Location Traps State Traps Primary Destination Table 10-5 SNMP Description Select Enabled to enable SNMP. Enter the SNMP read-only community string. Enter the SNMP read/write community string. Enter the name of the system contact. Enter the system name. Enter the system description. Enter the system location. Select Enabled to enable the transmission of SNMP Traps. The Cold Start trap is sent on device boot up, and the Linkdown trap is sent when the device is rebooted from software control. Enter the primary SNMP trap host. EDS1100/2100 User Guide 72

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
10: Service Settings
EDS1100/2100 User Guide
72
SNMP Settings
Simple Network Management Protocol (SNMP) is a network management tool that monitors
network devices for conditions that need attention. The SNMP service responds to SNMP
requests and generates SNMP Traps.
This page is used to configure the SNMP agent.
To configure SNMP:
1.
Click
SNMP
on the menu bar. The SNMP page opens and shows the current SNMP
configuration.
Figure 10-4
SNMP Configuration
2.
Enter or modify the following settings:
Table 10-5
SNMP
SNMP Settings
Description
State
Select
Enabled
to enable SNMP.
Read Community
Enter the SNMP read-only community string.
Write Community
Enter the SNMP read/write community string.
System Contact
Enter the name of the system contact.
System Name
Enter the system name.
System Description
Enter the system description.
System Location
Enter the system location.
Traps State
Select
Enabled
to enable the transmission of SNMP Traps.
The Cold Start trap is sent on device boot up, and the
Linkdown trap is sent when the device is rebooted from
software control.
Traps Primary Destination
Enter the primary SNMP trap host.