Home » Lenovo Manuals » Desktops » Lenovo ThinkCentre M51 » Manual Viewer

Lenovo ThinkCentre M51 Hardware Maintenance Manual - Page 48

Types - 8141

Get Lenovo ThinkCentre M51 PDF manuals and user guides

View all Lenovo ThinkCentre M51 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

Types 8095, 8096, 8141, 8142, 8145, 8420, and 8421 This section lists the physical specifications. Dimensions Height: 146 mm (5.7 in.) Width: 442 mm (17.4 in.) Depth: 401 mm (15.8 in.) Heat output (approximate) in British thermal units (Btu) per hour: Minimum configuration: 256 Btu/hr (75 watts) Maximum configuration: 1058 Btu/hr (310 watts) Weight Airflow Minimum configuration as shipped: 11 kg (24 lb) Maximum configuration: 14 kg (31 lb) Approximately 1.13 cubic meters per minute (40 cubic feet per minute) maximum Environment Air temperature: System on: 10° to 35°C (50° to 95° F) System off: 10° to 43°C (50° to 110° F) Acoustical noise-emission values Average sound-pressure levels: At operator position: (0.5 meters) Idle: 33 dBA Maximum altitude: 2134 m (7000 ft) Operating: 35 dBA Note: The maximum altitude, 2134 m (7000 ft), is the At bystander position - 1 meter (3.3 ft): maximum altitude at which the specified air temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified. Idle: 29 dBA Operating: 31 dBA Humidity: Declared (upper limit) sound-power levels: System on: 8% to 80% Idle: 4.3 bels System off: 8% to 80% Operating: 4.4 bels Electrical input Input voltage: Low range: Minimum: 90 V ac Maximum: 180 V ac Input frequency: 50/60 Hz Voltage switch setting: 115 V ac Note: These levels were measured in controlled acoustical environments according to the procedures specified by the American National Standards Institute (ANSI) S12.10 and ISO 7779 and are reported in accordance with ISO 9296. Actual sound-pressure levels in a given location might exceed the average values stated because of room reflections and other nearby noise sources. The declared sound-power levels indicate an upper limit, below which a large number of computers will operate. High range: Minimum: 137 V ac Maximum: 265 V ac Input frequency: 50/60 Hz Voltage switch setting: 230 V ac Input kilovolt-amperes (kVA) (approximate): Minimum configuration as shipped: 0.08 kVA Maximum configuration: 0.25 kVA Note: Power consumption and heat output vary depending on the number and type of optional features installed and the power-management optional features in use. 42 Hardware Maintenance Manual

Section	Page
Contents	5
Chapter 1. About this manual	7
Important Safety Information	7
Strategy for replacing FRUs for CTO, CMV, and GAV products	8
Product definition	8
FRU Identification for CTO, CMV, and GAV products	8
Using PEW	8
Using eSupport	9
Using the HMM	9
Important information about replacing RoHS compliant FRUs	9
Chapter 2. Safety information	11
General safety	11
Electrical safety	11
Safety inspection guide	13
Handling electrostatic discharge-sensitive devices	14
Grounding requirements	14
Safety notices (multi-lingual translations)	15
Chapter 3. General information	47
The Access IBM program	47
Additional information resources	47
Physical specifications	47
Types 8095, 8096, 8141, 8142, 8145, 8420, and 8421	48
Types 8097, 8143, 8144, 8146, 8422, 8423 and 8427	49
Types 8098, 8171, 8172, 8173, 8424, and 8425	50
Chapter 4. General Checkout	51
Problem determination tips	52
Chapter 5. Diagnostics using PC-Doctor for DOS	55
Starting PC-Doctor from the Rescue and Recovery workspace	55
Starting PC-Doctor from a diagnostic diskette or CD-ROM	56
Diagnostics program download	56
Navigating through the diagnostics programs	56
Running diagnostics tests	56
Test selection	57
Test results	57
Fixed disk advanced test (FDAT)	57
Quick and Full erase - hard drive	59
Viewing the test log	60
Chapter 6. Using the Setup Utility	61
Starting the Setup Utility program	61
Viewing and changing settings	61
Exiting from the Setup Utility program	61
Using passwords	61
Password considerations	62
User Password	62
Administrator Password	62
IDE Drive User Password	62
IDE Drive Master Password	62
Setting, changing, and deleting a password	63
Using Security Profile by Device	63
Selecting a startup device	64
Selecting a temporary startup device	64
Changing the startup device sequence	64
Advanced settings	64
Chapter 7. Symptom-to-FRU Index	65
Hard disk drive boot error	65
Power Supply Errors	65
Diagnostic error codes	67
Beep symptoms	88
No-beep symptoms	90
POST error codes	91
Miscellaneous error messages	94
Undetermined problems	96
Chapter 8. Replacing FRUs (Types 8095, 8141, 8142, 8145, 8420, and 8421)	97
Locating controls and connectors on the front of the computer	97
Locating connectors on the rear of the computer	98
Removing the cover	98
Locating components	100
Identifying parts on the system board	101
Removing and replacing memory	102
Removing and replacing a PCI adapter	103
Removing and replacing the battery	104
Removing and replacing the power supply	105
Removing and replacing the system board	107
Removing and replacing the microprocessor	109
Removing and replacing the hard disk drive	115
Removing and replacing the optical drive	116
Removing and replacing the diskette drive	117
Removing and replacing the fan assembly	118
Closing the cover and connecting cables	119
Chapter 9. Replacing FRUs (Types 8143, 8144, 8146, 8422, 8423, and 8427)	121
Locating controls and connectors on the front of the computer	121
Locating connectors on the rear of the computer	122
Removing the cover	122
Locating components	123
Identifying parts on the system board	124
Removing and replacing memory	125
Removing and replacing a PCI adapter	126
Removing and replacing the battery	127
Removing and replacing the power supply	127
Removing and replacing the system board	130
Removing and replacing the microprocessor	132
Removing and replacing the hard disk drive	137
Removing and replacing the optical drive	138
Removing and replacing the diskette drive	139
Removing and replacing the fan assembly	140
Replacing the cover and connecting the cables	141
Chapter 10. Replacing FRUs (Types 8098, 8171, 8172, 8173, 8424, and 8425)	143
Locating controls and connectors on the front of the computer	143
Locating connectors on the rear of the computer	144
Opening the cover	144
Locating components	145
Identifying parts on the system board	146
Removing and replacing memory	147
Replacing a PCI adapter	148
Removing and replacing the battery	149
Removing and replacing the power supply	149
Removing and replacing the system board	152
Removing and replacing the microprocessor	153
Removing and replacing the hard disk drive	158
Removing and replacing the optical drive	159
Removing and replacing the diskette drive	160
Removing and replacing the fan assembly	160
Removing and replacing the internal speaker	163
Removing and replacing the power button and LED assembly	163
Closing the cover and connecting cables	165
Chapter 11. FRU lists	167
Machine Type 8095	167
Machine Type 8098	173
Machine Type 8141	178
Machine Type 8142	193
Machine Type 8143	204
Machine Type 8144	220
Machine Type 8145	230
Machine Type 8146	237
Machine Type 8171	243
Machine Type 8172	261
Machine Type 8173	271
Machine Type 8420	278
Machine Type 8421	286
Machine Type 8422	293
Machine Type 8423	304
Machine Type 8424	316
Machine Type 8425	325
Machine Type 8427	334
Chapter 12. Additional Service Information	343
Security features	343
Hardware controlled Passwords	343
Operating system password	343
Vital product data	343
Management Information Format (MIF)	343
BIOS levels	344
Flash update procedures	344
Updating (flashing) BIOS from a diskette or CD-ROM	344
Updating (flashing) BIOS from your operating system	344
Recovering from a POST/BIOS update failure	345
Power management	346
Automatic configuration and power interface (ACPI) BIOS	346
Automatic Power-On features	346
Recovering software using the Rescue and Recovery program	347
Starting the Rescue and Recovery workspace	347
Appendix. Notices	349
Television output notice	350

Match case Limit results 1 per page

Types

8095,

8096,

8141,

8142,

8145,

8420,

and

8421

This

section

lists

the

physical

specifications.

Dimensions

Height:

146

(5.7

in.)

Width:

442

(17.4

in.)

Depth:

401

(15.8

in.)

Weight

Minimum

configuration

shipped:

(24

lb)

Maximum

configuration:

(31

lb)

Environment

Air

temperature:

System

on:

10°

35°C

(50°

95°

System

off:

10°

43°C

(50°

110°

Maximum

altitude:

2134

(7000

ft)

Note:

The

maximum

altitude,

2134

(7000

ft),

the

maximum

altitude

which

the

specified

air

temperatures

apply.

higher

altitudes,

the

maximum

air

temperatures

are

lower

than

those

specified.

Humidity:

System

on:

80%

System

off:

80%

Electrical

input

Input

voltage:

Low

range:

Minimum:

Maximum:

180

Input

frequency:

50/60

Voltage

switch

setting:

115

High

range:

Minimum:

137

Maximum:

265

Input

frequency:

50/60

Voltage

switch

setting:

230

Input

kilovolt-amperes

(kVA)

(approximate):

Minimum

configuration

shipped:

0.08

kVA

Maximum

configuration:

0.25

kVA

Note:

Power

consumption

and

heat

output

vary

depending

the

number

and

type

optional

features

installed

and

the

power-management

optional

features

use.

Heat

output

(approximate)

British

thermal

units

(Btu)

per

hour:

Minimum

configuration:

256

Btu/hr

(75

watts)

Maximum

configuration:

1058

Btu/hr

(310

watts)

Airflow

Approximately

1.13

cubic

meters

per

minute

(40

cubic

feet

per

minute)

maximum

Acoustical

noise-emission

values

Average

sound-pressure

levels:

operator

position:

(0.5

meters)

Idle:

dBA

Operating:

dBA

bystander

position

meter

(3.3

ft):

Idle:

dBA

Operating:

dBA

Declared

(upper

limit)

sound-power

levels:

Idle:

4.3

bels

Operating:

4.4

bels

Note:

These

levels

were

measured

controlled

acoustical

environments

according

the

procedures

specified

the

American

National

Standards

Institute

(ANSI)

S12.10

and

ISO

7779

and

are

reported

accordance

with

ISO

9296.

Actual

sound-pressure

levels

given

location

might

exceed

the

average

values

stated

because

room

reflections

and

other

nearby

noise

sources.

The

declared

sound-power

levels

indicate

upper

limit,

below

which

large

number

computers

will

operate.

Hardware

Maintenance

Manual