Lenovo ThinkPad T430s Hardware Maintenance Manual - ThinkPad T430s and T430si - Page 99

thin film off from the rubber, Turn the system board over

Get Lenovo ThinkPad T430s PDF manuals and user guides View all Lenovo ThinkPad T430s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Turn the system board over, and then disconnect the thermal fan assembly from the system board. 6 7 6 8 Step 7 Screw (quantity) M2 × 5 mm, big-head, nylon-coated (4) Color Black Torque 0.181 Nm (1.85 kgfcm) When installing: • Before you attach the thermal fan assembly to the computer, apply thermal grease, at an amount of 0.2 grams, on the part marked a as in the following illustration. Either too much or too less application of grease can cause a thermal problem due to imperfect contact with a component. You need to peel the thin film off from the rubber b . • Make sure that the fan connector is attached firmly. a b Remove the three screws and then remove the 34-mm ExpressCard reader from the system board. Chapter 9. Removing or replacing a FRU 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
Turn the system board over, and then disconnect the thermal fan assembly from the system board.
8
6
7
Step
Screw (quantity)
Color
Torque
7
M2 × 5 mm, big-head, nylon-coated (4)
Black
0.181 Nm
(1.85 kgfcm)
When installing:
•
Before you attach the thermal fan assembly to the computer, apply thermal grease, at an amount of 0.2
grams, on the part marked
a
as in the following illustration. Either too much or too less application of
grease can cause a thermal problem due to imperfect contact with a component. You need to peel the
thin film off from the rubber
b
.
•
Make sure that the fan connector is attached firmly.
Remove the three screws and then remove the 34-mm ExpressCard reader from the system board.
Chapter 9
.
Removing or replacing a FRU
93