Lexmark 2050 Color Jetprinter Service Manual - Page 27

Diagnostic Aids, Encoder Sensor Test, Diagnostic Aids 3-1

Get Lexmark 2050 Color Jetprinter PDF manuals and user guides View all Lexmark 2050 Color Jetprinter manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3. Diagnostic Aids Use these diagnostic test procedures to verify a repair. Encoder Sensor Test This test disables the printer motors to allow you to manually move the carrier to verify the encoder is working correctly. To run the test: 1. Turn the printer off. 2. Remove the front cover. 3. Disconnect the transport motor connector J-6 at the system board. 4. Turn the printer on. 5. After a few seconds, the power light blinks 1 time. The power light blinks as the carrier moves. If the test fails, power off the printer and remove the carrier assembly without unplugging the printhead cable. Power on the printer and check for +5 V dc at pins 1, 2 and 3 of the encoder card connector. 1. If voltage is not present, check the printhead cable for opens to the encoder card. If the printhead cable is good, replace the system board. 2. If voltage is present, check the sensor on the encoder card by monitoring pin 3 of the encoder card connector as you pass a piece of paper through the sensor. The voltage should go from +5 V dc to 0 V dc. Turn the power off and back on to make this check again. If the voltage at pin 3 does not change, replace the encoder card. If the symptom remains, replace the printhead cable. Diagnostic Aids 3-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Diagnostic Aids 3-1
3.
Diagnostic Aids
Use these diagnostic test procedures to verify a repair.
Encoder Sensor Test
This test disables the printer motors to allow you to manually move
the carrier to verify the encoder is working correctly.
To run the test:
1. Turn the printer off.
2. Remove the front cover.
3. Disconnect the transport motor connector J-6 at the system
board.
4. Turn the printer on.
5. After a few seconds, the power light blinks 1 time. The power
light blinks as the carrier moves.
If the test fails, power off the printer and remove the carrier assembly
without unplugging the printhead cable.
Power on the printer and check for +5 V dc at pins 1, 2 and 3 of the
encoder card connector.
1.
If voltage is not present, check the printhead cable for opens to
the encoder card. If the printhead cable is good, replace the
system board.
2.
If voltage is present, check the sensor on the encoder card by
monitoring pin 3 of the encoder card connector as you pass a
piece of paper through the sensor. The voltage should go from
+5 V dc to 0 V dc. Turn the power off and back on to make this
check again. If the voltage at pin 3 does not change, replace the
encoder card. If the symptom remains, replace the printhead
cable.