Marantz SR7005 SR7005 User Manual - English - Page 85

Simple version Basic version SVENSKA NEDERLANDS Setting items Speaker Config. (Continued) Bass Setting Set subwoofer and LFE signal range playback. Setting details F.Wide : Set the presence and size of the front wide speakers. • Large : Use a large speaker that can adequately play back low frequencies. • Small : Use a small speaker that has inadequate playback capacity for low frequencies. • None : Select when the front wide speakers are not connected. NOTE When "Amp Assign" setting (vpage 80) is other than "Normal", you cannot make the "F.Wide" setting. Subwoofer Mode : Select low range signals to be reproduced by subwoofer. • LFE : The low range signal of the channel set to "Small" speaker size is added to the LFE signal output from the subwoofer. • LFE+Main : The low range signal of all channels is added to the LFE signal output from the subwoofer. Distance Set distance from listening position to speakers. Measure beforehand the distance from the listening position to each speaker. • "Subwoofer Mode" can be set when "Speaker Config." - "Subwoofer" (vpage 80) is set to "Yes". • Play music or a movie source and select the mode offering the strongest bass. • Select "LFE+Main" if you want the bass signals to always be produced from the subwoofer. NOTE If "Front" and "Center" for "Speaker Config." are set to "Large", and "Subwoofer Mode" is set to "LFE", no sound may be output from the subwoofers, depending on the input signal or selected surround mode. LPF for LFE : Set LFE signal playback range. • 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz Unit : Set the unit of distance. • Feet / Meters Step : Set the minimum variable width of the distance. • 1ft / 0.1ft • 0.1m / 0.01m Front L / Front R / Center / Subwoofer / Surround L / Surround R / S.Back Lz / S.Back Rz / F.Height L / F.Height R / F.Wide L / F.Wide R : Select the speaker. zz When the "Speaker Config." - "S.Back" setting (vpage 80) is set to "1spkr", "S.Back" is displayed. • 0.0ft - 60.0ft / 0.00m - 18.00m : Set the distance. ESPAÑOL ITALIANO FRANÇAIS DEUTSCH ENGLISH Manual Setup Setting items Distance (Continued) Setting details • The speakers that can be selected differ depending on the "Amp Assign" (vpage 80) and "Speaker Config." (vpage 80) settings. • Default settings : Front L / Front R / Center / Subwoofer / F.Height L / F.Height R / F.Wide L / F.Wide R : 12.0 ft (3.6 m) Surround L / Surround R / S.Back L / S.Back R : 10.0 ft (3.0 m) • Set the difference in the distance between the speakers to less than 20 ft (6.0 m). NOTE Speakers set to "None" in "Speaker Config." (vpage 80) are not displayed. Default : The "Distance" settings are returned to the default settings. • Yes : Reset to the defaults. • No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Default Setting?" prompt is displayed. Select either "Yes" or "No", and press ENTER. Channel Level Test Tone Start : Output test tone. Set the volume of the test • Front L / F.Height L / Center / F.Height R / Front R / F.Wide R / tone to be the same when it Surround R / S.Back Rz / S.Back Lz / Surround L / F.Wide L / is output from each speaker. Subwoofer : Select the speaker. zz When the "Speaker Config." - "S.Back" setting (vpage 80) is set to "1spkr", "S.Back" is displayed. • -12.0dB - +12.0dB (0.0dB) : Adjust the volume. • When o is pressed while the subwoofer volume is set to "-12 dB", the "Subwoofer" setting switches to "OFF". • When "Channel Level" is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different surround modes, use the operation see page 58. • When you press TEST TONE on the remote control unit, you can enter this setting item immediately. NOTE • Speakers set to "None" in the "Speaker Config." (vpage 80) settings are not displayed. • When a headphones jack is inserted in the PHONES jack of this unit, the "Channel Level" is not displayed. Default : The "Channel Level" settings are returned to the default settings. • Yes : Reset to the defaults. • No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Default Setting?" prompt is displayed. Select either "Yes" or "No", and press ENTER. Advanced version Information Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu 81