Marantz SR7005 SR7005 User Manual - English - Page 9

Install, Connect - set

Get Marantz SR7005 PDF manuals and user guides View all Marantz SR7005 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Simple version Basic version 1 Install SVENSKA NEDERLANDS 1 2345 ESPAÑOL ITALIANO 2 Connect FRANÇAIS DEUTSCH ENGLISH 1 2345 This unit can perform 2.0/2.1 to 7.1-channel surround playback. This page provides the speaker installation procedure for the 7.1-channel playback using surround back speakers as an example. The default setting is 7.1-channel. You can also perform 5.1-channel playback. To perform 5.1-channel playback, connect5.1-channel speakers only. Use Audyssey Auto Setup function of this unit to automatically detect the number of connected speakers and perform optimal settings for the speakers to be used. FL SW FR C 90 - 110˚ 22 - 30˚ 135 - 150˚ Speakers Carefully check the left (L) and right (R) channels and + (red) and - (black) polarities on the speakers being connected to the this unit, and be sure to interconnect the channels and polarities correctly. Connecting the speaker cables Peel off about 0.03 ft/10 mm of sheathing from the tip of the speaker cable, then either twist the core wire tightly or terminate it. NOTE • Connect so that the speaker cable core wires do not protrude from the speaker terminal. The protection circuit may be activated if the core wires touch the rear panel or if the + and - sides touch each other (vpage 113 "Protection Circuit"). • Never touch the speaker terminals while the power supply is connected. Doing so could result in electric shock. • Use speakers with the speaker impedances shown below. Speaker terminals FRONT A FRONT A + FRONT B CENTER SURROUND SURR. BACK / AMP ASSIGN FRONT B/HEIGHT FRONT WIDE Speaker impedance 6 − 8 Ω 8 Ω 6 − 8 Ω SL SR Listening position SBL SBR Advanced version Information FL Front speaker (L) FR Front speaker (R) C Center speaker SW Subwoofer SL Surround speaker (L) SR Surround speaker (R) SBL Surround back speaker (L) SBR Surround back speaker (R) • Install the surround speakers in a position 2 to 3 ft (60 to 90 cm) higher than ear level. Surround speaker Front speaker 2 - 3 ft / 60 - 90 cm Surround back speaker • Point slightly downwards GViewed from the sideH The "Simple version" section provides the speaker installation, connection, and setup methods for the 7.1-channel system with surround back speakers. 5 For the installing, connecting, and setup methods of speakers other than the 7.1-channel system (with surround back speakers), see page 50 .

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
5
Basic version
Advanced version
Information
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
SVENSKA
Simple version
Speakers
Carefully check the left (L) and right (R)
channels and + (red) and – (black) polarities
on the speakers being connected to the
this unit, and be sure to interconnect the
channels and polarities correctly.
Connecting the speaker cables
Peel off about 0.03 ft/10 mm of sheathing from
the tip of the speaker cable, then either twist the
core wire tightly or terminate it.
NOTE
•
Connect so that the speaker cable core wires
do not protrude from the speaker terminal.
The protection circuit may be activated if the
core wires touch the rear panel or if the + and –
sidestoucheachother(
v
page 113“Protection
Circuit”).
•
Never touch the speaker terminals while the
power supply is connected. Doing so could
result in electric shock.
•
Use speakers with the speaker impedances
shown below.
Speaker terminals
Speaker
impedance
FRONT A
6 − 8 Ω
FRONT A
+ FRONT B
8 Ω
CENTER
6 − 8 Ω
SURROUND
SURR. BACK / AMP ASSIGN
FRONT B/HEIGHT
FRONT WIDE
Install
1
2
3
4
5
This unit can perform 2.0/2.1 to 7.1-channel surround playback.
This page provides the speaker installation procedure for the
7.1-channel playback using surround back speakers as an example.
The default setting is 7.1-channel. You can also perform 5.1-channel playback.
To perform 5.1-channel playback, connect5.1-channel speakers only.
Use Audyssey Auto Setup function of this unit to automatically detect the
number of connected speakers and perform optimal settings for the speakers
to be used.
FL
FR
C
SBL
SBR
SL
SR
SW
90 – 110˚
22 – 30˚
135 – 150˚
Listening
position
FL
Front speaker (L)
• Install the surround speakers in a position 2 to
3 ft (60 to 90 cm) higher than ear level.
Surround back
speaker
• Point slightly
downwards
Front
speaker
Surround
speaker
2 – 3 ft /
60 – 90 cm
G
Viewed from the side
H
FR
Front speaker (R)
C
Center speaker
SW
Subwoofer
SL
Surround speaker (L)
SR
Surround speaker (R)
SBL
Surround back speaker (L)
SBR
Surround back speaker (R)
1
Connect
1
2
3
4
5
2
The “Simple version” section provides the speaker installation, connection, and setup methods for the 7.1-channel system with surround back speakers.
For the installing, connecting, and setup methods of speakers other than the 7.1-channel system (with surround back speakers), see page 50 .