Maytag MMMF8030PZ Bump Out Kit Installation Instructions - Page 7

Mark Rear Wall, Drill Holes in Upper Cabinet

Get Maytag MMMF8030PZ PDF manuals and user guides View all Maytag MMMF8030PZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

6. Place and tape the upper cabinet template against the bottom of the upper cabinet. NOTES: ■ Make sure the L line on the upper cabinet template align with the back edge of upper cabinet. ■ Make sure the center marks on the upper cabinet template align with the upper cabinet centerline which draw in step 1. NOTE: If the front edge of the upper cabinet is lower than the back edge, lower the wall template so that its top is level with the front edge of the cabinet. D A C B D 13"< L ≤14" A BC 13"< L ≤14" A. Upper Cabinet Centerline and Upper Cabinet Template Centerline B. Back edge of the Upper Cabinet C. L Line on Upper Cabinet Template D. Center Marks on Upper Cabinet Template Mark Rear Wall The microwave oven must be installed on a minimum of 1 wall stud, preferably 2, using a minimum of 1 lag screw, preferably 2. See "Find the Wall Stud(s)" section for find the wall studs. 1. Using measuring tape, find and clearly mark the vertical centerline of the opening. A. Rear wall B. Back edge of the Upper Cabinet C. Top of wall template must align with front edge of cabinet D. Front edge of upper cabinet Drill Holes in Upper Cabinet 1. Using a 3/4" (1.9 cm) hole saw, cut out the power cord hole (A), which is "G" on the upper cabinet template. 2. Drill two mounting nut holes (B), which are 3/8" (10 mm) holes at points "D" and "E" on the upper cabinet template. These are for two 1/4-20 x 3" bolts and washers used to secure the microwave oven to the upper cabinet. B A A A. Centerline 2. Tape the Wall template in place. Align the center mark on the wall template over the vertical centerline draw in step 1. Make sure the wall template is level, and that the top of the wall template is butted up against the bottom edge of the upper cabinet. A. Power Cord Hole B. Mounting Nut Holes NOTE: If upper cabinet is metal, the supply cord bushing needs to be installed around the supply cord hole as shown. B A A B C A. Metal cabinet B. Power supply cord bushing A. Bottom Edge of Upper Cabinet and Top of the Wall Template B. Center Marks on Wall Template C. Centerline 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
7
6.
Place and tape the upper cabinet template against the
bottom of the upper cabinet.
NOTES:
■
Make sure the L line on the upper cabinet template align
with the back edge of upper cabinet.
■
Make sure the center marks on the upper cabinet
template align with the upper cabinet centerline which
draw in step 1.
Mark Rear Wall
The microwave oven must be installed on a minimum of 1 wall
stud, preferably 2, using a minimum of 1 lag screw, preferably 2.
See “Find the Wall Stud(s)” section for find the wall studs.
1.
Using measuring tape, find and clearly mark the vertical
centerline of the opening.
2.
Tape the Wall template in place. Align the center mark on the
wall template over the vertical centerline draw in step 1. Make
sure the wall template is level, and that the top of the wall
template is butted up against the bottom edge of the upper
cabinet.
NOTE:
If the front edge of the upper cabinet is lower than the
back edge, lower the wall template so that its top is level with the
front edge of the cabinet.
Drill Holes in Upper Cabinet
1.
Using a 3/4" (1.9 cm) hole saw, cut out the power cord hole
(A), which is “G” on the upper cabinet template.
2.
Drill two mounting nut holes (B), which are 3/8" (10 mm) holes
at points “D” and “E” on the upper cabinet template. These
are for two 1/4-20 x 3" bolts and washers used to secure the
microwave oven to the upper cabinet.
NOTE:
If upper cabinet is metal, the supply cord bushing
needs to be installed around the supply cord hole as shown.
A
D
C
B
13”< L ≤14”
13”< L ≤14”
A. Upper Cabinet Centerline and Upper
Cabinet Template Centerline
B. Back edge of the Upper Cabinet
C. L Line on Upper Cabinet Template
D. Center Marks on Upper Cabinet Template
A. Centerline
A
A. Bottom Edge of Upper Cabinet and Top of
the Wall Template
B. Center Marks on Wall Template
C. Centerline
A
C
B
D
A. Rear wall
B. Back edge of the Upper Cabinet
C. Top of wall template must align
with front edge of cabinet
D. Front edge of upper cabinet
A
B
A. Power Cord Hole
B. Mounting Nut Holes
B
A
C
A
B
A. Metal cabinet
B. Power supply cord bushing