Miele Triflex HX2 Operating instructions/Installation instructions - Page 182

PowerUnit connector.

Get Miele Triflex HX2 PDF manuals and user guides View all Miele Triflex HX2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 182 highlights

en-US  Risk of damage caused by incor- rect cleaning. The fine dust filter can become damaged and be less effective as a result. Do not clean the fine dust filter with water and avoid cleaning the inside. Do not use pointed or sharp-edged objects to clean the filter. Do not brush the fine dust filter.  Hold the fine dust filter over a garbage can.  Carefully knock the fine dust filter with the rubberized lower edge.  Turn the fine dust filter slightly while you do this to free the dirt from all of the crevices.  Risk of damage caused by incor- rect cleaning. The pre-filter can become damaged and be less effective as a result. Do not clean the pre-filter with water. Do not use pointed or sharp-edged objects to clean the filter.  Clean the pre-filter with the dusting brush supplied or with a dry cloth.  After cleaning the fine dust filter and pre-filter, reinsert the former into the latter by pressing the round cap on top of the fine dust filter down as far as it will go. To continue achieving the best possible cleaning results, replace the fine dust filter (HX FSF-2) with a new one after approx. 3 years.  Reinsert the pre-filter in the dust container (Fig. 41). 182  To do this, line up the guides (arrows) and turn the pre-filter back to its original position (Fig. 42).  Close the dust container flap, making sure it clicks into place.  Replace the dust container on the PowerUnit connector. Cleaning the dust container Clean the dust container as required.  Remove the dust container.  Empty the dust container over a garbage can and lift the pre-filter upward to remove it (Fig. 39).  Clean the dust container using water and mild detergent.  Dry the dust container carefully.  Reinsert the pre-filter in the dust container and turn the pre-filter back to its original position (Figs. 41 + 42).  Replace the dust container on the PowerUnit connector. Cleaning the Electrobrush/handheld brush (depending on model) (Fig. 43)  Disconnect the Electrobrush/handheld brush from the vacuum cleaner (Fig. 10).  Place the Electrobrush/handheld brush upside down on a level, clean surface.  Use a pair of scissors to cut any threads or hairs that have wound themselves around the roller brush. To guide the scissors, move along the guide track on the roller brush.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
en-US
182
Risk of damage caused by incor-
rect cleaning.
The fine dust filter can become dam-
aged and be less effective as a re-
sult.
Do not clean the fine dust filter with
water and avoid cleaning the inside.
Do not use pointed or sharp-edged
objects to clean the filter. Do not
brush the fine dust filter.
Hold the fine dust filter over a
garbage can.
Carefully knock the fine dust filter
with the rubberized lower edge.
Turn the fine dust filter slightly while
you do this to free the dirt from all of
the crevices.
Risk of damage caused by incor-
rect cleaning.
The pre-filter can become damaged
and be less effective as a result.
Do not clean the pre-filter with water.
Do not use pointed or sharp-edged
objects to clean the filter.
Clean the pre-filter with the dusting
brush supplied or with a dry cloth.
After cleaning the fine dust filter and
pre-filter, reinsert the former into the
latter by pressing the round cap on
top of the fine dust filter down as far
as it will go.
To continue achieving the best possi-
ble cleaning results, replace the fine
dust filt
er (HX FSF-2) with a new one
after appro
x. 3 years.
Reinsert the pre-filter in the dust con-
tainer (Fig. 41).
To do this, line up the guides (arrows)
and turn the pre-filter back to its orig-
inal position (Fig. 42).
Close the dust container flap, making
sure it clicks into place.
Replace the dust container on the
PowerUnit connector.
Cleaning the dust container
Clean the dust container as required.
Remove the dust container.
Empty the dust container over a
garbage can and lift the pre-filter up-
ward to remove it (Fig. 39).
Clean the dust container using water
and mild detergent.
Dry the dust container carefully.
Reinsert the pre-filter in the dust con-
tainer and turn the pre-filter back to
its original position (Figs. 41 + 42).
Replace the dust container on the
PowerUnit connector.
Cleaning the Electrobrush/handheld
brush (depending on model) (Fig. 43)
Disconnect the Electrobrush/hand-
held brush from the vacuum cleaner
(Fig. 10).
Place the Electrobrush/handheld
brush upside down on a level, clean
surface.
Use a pair of scissors to cut any
threads or hairs that have wound
themselves around the roller brush.
To guide the scissors, move along the
guide track on the roller brush.